CUB4I000 Red Lion Controls, CUB4I000 Datasheet - Page 2

• Manufacturer Part Number: CUB4I000
• Description: DC Current Meter, Reflective Display
• Manufacturer: Red Lion Controls
• Series: CUB4r
• Type: Ammeterr

Specifications of CUB4I000

• Measuring Range: 0 ~ 199.9mA
• Display Style: Black Characters, Grey Background
• Display Type: LCD
• Display Face Size: 2.95" L x 1.54" W (74.9 x 39.1mm)
• Display Digits: 3.5
• Display Digits - Height: 0.600" (15.24mm)
• Backlight: Without
• Mounting Type: Panel Mount
• Termination: Screw Terminals
• Voltage - Supply: 9 ~ 28VDC
• Accuracy: ±0.1% (199.9 µA to 19.99 mA)
• Application: Used in Industrial Environments
• Bezel: NEMA 4X⁄IP65 Sealed Front Panel
• Brand/series: CUB
• Connection Type: Screw-Clamp
• Current, Rating: ±199.9 mAdc (Max.)
• Cut Out, Panel: 2.68×1.3 "
• Digit Height: 0.6
• Dimensions: 2.95"L×2.11"W×1.54"H
• Display Digit Height: 0.6 "
• Function: Ammeter
• Humidity: 85% (Max.) @ 60 °C (Non-Condensing)
• Indicator Type: 3-1⁄2 Digit
• Material, Casing: Plastic
• Meter Type: DC Current
• Number Of Digits: 3-1/2
• Primary Type: Electronic
• Range, Measurement: ±199.9 μADC to ±199.9 mADC
• Special Features: programmable
• Standards: cULus Recognized
• Temperature, Operating: 0 to 60 °C
• Voltage, Supply: 9 to 28 VDC
• Panel Cutout: 2.68" × 1.30"
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: Q1156337

10. INPUT IMPEDANCE:
11. CERTIFICATIONS AND COMPLIANCES:
INSTALLATION ENVIRONMENT
exceed the maximum operating temperature and provides
good air circulation. Placing the unit near devices that
generate excessive heat should be avoided. The bezel should
be cleaned only with a soft cloth and neutral soap product.
Do NOT use solvents.
aging process of the bezel.
etc.) to operate the keypad of the unit.
Installation
NEMA 4X/IP65 requirements for indoor use, when properly
installed. The units are intended to be mounted into an enclosed panel. A
sponge rubber gasket, mounting clip, two screws, and nut fasteners are
provided to install and seal the unit in the panel cutout.
1. Cut panel opening to specified dimensions. Remove burrs and clean panel
2. Carefully remove center section of the panel gasket and discard. Slide
3. Slide nut fastener into slot on mounting clip and then insert mounting screw
4. Install CUB4 unit through panel cutout.
5. Slide mounting clip over rear of unit until clip is against back of panel. The
Note: Hold the CUB4 front bezel in place when sliding the mounting clip into
6. Alternately tighten each mounting screw to ensure uniform gasket pressure.
Voltmeter: 1 MΩ
Current Meter:
SAFETY
ELECTROMAGNETIC COMPATIBILITY
Immunity to EN 50082-2
Electrostatic discharge
Electromagnetic RF fields
Fast transients (burst)
RF conducted interference
Power frequency magnetic fields
Simulation of cordless telephone
Emissions to EN 50081-2
RF interference
The unit should be installed in a location that does not
Continuous exposure to direct sunlight may accelerate the
Do not use tools of any kind (screwdrivers, pens, pencils,
The CUB4 Volt and Current meters meet
The following procedure assures proper installation:
opening.
gasket over rear of the unit to the back of the bezel.
through nut on both sides of mounting clip. Tip of mounting screw should
NOT project through hole on clip.
mounting clip and CUB4 housing have a latching feature to hold the unit in
place until tightened.
position.
Visually inspect the gasket for proper seal. The gasket should be
compressed approximately 75 to 80% of its original thickness.
(Recommended torque is 28 to 36 in-oz.)
199.9 µA - 1 KΩ
1.999 mA - 100 Ω
19.99 mA - 10 Ω
199.9 mA - 1 Ω
UL Recognized Component, File # E179259, UL3101-1, CSA C22.2 No. 1010-1
Type 4X Enclosure rating (Face only), UL50
IECEE CB Scheme Test Certificate # UL2356A-179259/USA,
Recognized to U.S. and Canadian requirements under the Component
Recognition Program of Underwriters Laboratories, Inc.
CB Scheme Test Report # 98ME60090-000098
IEC 1010-1, EN 61010-1: Safety requirements for electrical equipment
IP65 Enclosure rating (Face only), IEC 529
Issued by Underwriters Laboratories, Inc.
for measurement, control, and laboratory use, Part 1.
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-6
EN 61000-4-8
ENV 50204
EN 55011
Level 2; 4 Kv contact
Level 3; 8 Kv air
Level 3; 10 V/m
80 MHz - 1 GHz
Level 4; 2 Kv I/O
Level 3; 2 Kv power
Level 3; 10 V/rms
150 KHz - 80 MHz
Level 4; 30 A/m
Level 3; 10 V/m
900 MHz ± 5 MHz
200 Hz, 50% duty cycle
Enclosure class A
Power mains class A
1
2
2
12. ENVIRONMENTAL CONDITIONS:
13. CONSTRUCTION: High impact plastic case with clear viewing window.
14. WEIGHT: 3.3 oz. (93.5 g)
7. If the gasket is not adequately compressed and the mounting screws cannot
8. Repeat step #6 for tightening the mounting screws.
Notes:
1. Self-recoverable loss of performance during EMI disturbance at 10 V/m.
2. Self-recoverable loss of performance during EMI disturbance at 10 Vrms.
Refer to the EMC Installation Guidelines section of this bulletin for
Operating Temperature: 0° to 60°C (above 50°C, derate backlight
Storage Temperature: -40° to 80°C
Operating and Storage Humidity: 85% max relative humidity (non-
Vibration According to IEC 68-2-6: 5 to 500 Hz, in X, Y, Z direction for
Shock According to IEC 68-2-27: Operational 30 g, 11 msec in 3 directions.
Temperature Coefficient: 100 PPM/°C
Altitude: Up to 2000 meters.
(Panel gasket and mounting clip included.) This unit is rated for NEMA
4X/IP65 indoor use. Installation Category II, Pollution Degree 2
be tightened any further, loosen mounting screws and insure that the clip is
latched as close as possible to the panel.
For operation without loss of performance:
For operation without loss of performance:
additional information.
operating voltage to 26 VDC maximum).
condensing) from 0 to 60°C.
1.5 hours, 5g’s.
Process signal may deviate during EMI disturbance.
Unit is mounted in a metal enclosure (Buckeye SM7013-0 or equivalent)
I/O and power cables are routed in metal conduit connected to earth
ground.
Process signal may deviate during EMI disturbance.
Install power line filter RLC#LFIL0000 or equivalent at the unit.