HS-5100-0346 LAMINA, HS-5100-0346 Datasheet - Page 24

• Manufacturer Part Number: HS-5100-0346
• Description: HEAT SINK, FOR TITAN LED
• Manufacturer: LAMINA

Specifications of HS-5100-0346

• Height: 25.4mm
• Heat Sink Material: Aluminium
• Svhc: No SVHC (18-Jun-2010)
• External Depth: 25mm
• External Length / Height: 136.9mm
• Surface Finish: Anonised
• External Diameter: 136.9mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

©2006 Lamina Ceramics
Lamina Titan Series LED Light Engines (FM-068 Rev
Patents
Lamina’s light engines may be covered by pending patents and/or one or more of the following U.S. and/or
International patents 5876536, 6709749 B, 595880, 607642, 5565262, 568444, 5653834, 558876, 5847935,
55445, 574793, 5925203, 5725808, 592950, 585845, 5866240, 5953203, 60555, 64076, 60330,
6399230, 69450, 668490, 69934, 64075, 660469, 6300267, 647805, 658502, 6739047, 6720859,
6759940, 658502, 6670856 B, 6720859, 673862 B2, WO 00/47399, WO 00/2652, WO 98/9339, 5082804,
ZL99808762.9, 69623930, 69628549, 69629572, 805785, 69628549, 84362, 932500, 805785, 82258, 84362,
932500, 805785, 82258, 84362, 932500, 805785, 82258, 84362, 932500, 3327556, 3267299, 322628,
3405545, 320630, 295695, 284068, 54647, 805785, 82258, 84362, 6455930, 6759940, 673862, 7095053,
7098483.
Electrical Connections
The Titan LED light engines connectors for solderless connections to Lamina’s wiring harness.
For more information refer to Lamina’s Connection application note which can be found on the website at www.
laminaceramics.com.
Functional test: Parts may be illuminated for functional test using a constant current source set at 25% of Drive
Current for no more than two seconds without heat sink. Voltage compliance of the power source should be no
greater than max forward voltage +5V.
1. Optical and electrical specifications are given for the specified drive @ 25ºC junction temperature.
2. When using constant current LED drivers with high compliance voltage (Advance, LEDworks, etc. or a custom
Assembly Recommendations
Lamina’s Titan Series Light Engines are designed for attachment to a heat sink with conductive epoxy, or screw
down for flange mount devices with thermal grease in the joint. For attachment using screws a 4-40 UNC round
head or metric equivalent M3 x 0.5 cheese head screw, 8-8 SS is recommended.When mounting the light engine,
position the four screws in the center of each of the four slots. Tighten the four screws evently, first to about 0.89
inch pounds (56 Newton-centimeters), and then tighten each to a maximum torque of 5 inch pounds (45 Newton-
centimeter). Flatness requirement of the surface that the light engine is mounted to is 0.00 inch/inch (mm/meter).
To prevent damage when using conductive epoxy do not use mounting screws.
All specifications are based on mounting the LED array to a heat sink using the specified hardware and thermal
grease (e.g. Wakefield P/N 120). The heat sink must meet the specified flatness requirement. Mounting using
screws and thermal tape may damage the device.
Receiving Parts and Packaging Trays
Your parts will arrive in custom fitted trays. This packaging was designed to provide the necessary protection during
shipment and to take up the least amount of space in your storage area.
Notes
1. “This product uses silicone materials for superior optical performance. Do not expose the part to fluids that may
2. Ray trace models are available upon request.
3. Lamina may make process or materials changes affecting the performance or other characteristics of our
4. All specifications are based on mounting the LED array to a heat sink using the specified hardware and thermal
driver) the output of the supply must be connected to the part before power is applied to the input of the
supply.
react with silicone compounds.” See Dow Chemical Form 45-03D-0, Silicone Fluid Resistance Guide.
products. These products supplied after such changes will continue to meet published specifications, but may
not be identical to product supplied as samples or under prior orders.
grease Wakefield 120. The heat sink must meet the specified flatness requirement. Mounting using screws and
thermal tape may damage the device.
0.30.06))
Titan
LED Light Engines
www.laminaceramics.com
24