HSDL-3211-021 Avago Technologies US Inc., HSDL-3211-021 Datasheet
HSDL-3211-021
Specifications of HSDL-3211-021
Related parts for HSDL-3211-021
HSDL-3211-021 Summary of contents
Page 1
... Data Compliant Low Power 1.15 Mbit/s ® Infrared Transceiver Data Sheet Description The HSDL-3211 is a new generation low profile high speed infrared transceiver module that provides interface between logic and IR signals for through- air, serial, half-duplex IR data-link. The module is fully compliant to IrDA Physical Layer specification version 1 ...
Page 2
... Application Support Information The Application Engineering Group is available to assist you with the application design Order Information Part Number Packaging Type HSDL-3211-021 Tape and Reel I/O Pins Configuration Table Pin Symbol Description 1 LED A LED Anode 2 LED C LED Cathode 3 TXD Transmit Data. Active High. ...
Page 3
CAUTIONS: The BiCMOS inherent to the design of this component increases the component’s susceptibility to damage from electrostatic discharge (ESD advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or ...
Page 4
Electrical & Optical Specifications Specifications (Min. & Max. values) hold over the recommended operating conditions unless otherwise noted. Unspecified test conditions may be anywhere in their operating range. All typical values (Typ.) are at 25°C, Vcc set to 3.0V and ...
Page 5
V OH 90% 50% 10 Figure 3. RxD output waveform. TXD LED t pw (MAX.) Figure 5. TxD “Stuck On” protection waveform. 0.18 0.16 0.14 0.12 0.10 0.08 0.06 0.04 0.02 0 1.4 1.5 ...
Page 6
... HSDL-3211 Package Dimensions 2.0 0.8 0.4 6 ...
Page 7
... HSDL-3211 Tape and Reel Dimensions Unit: mm 1.5 POLARITY Pin 8: GND Pin 1: LEDA 8.4 ± 0.1 0.4 ± 0.05 3.4 ± 0.1 2.8 ± 0.1 Empty Parts Mounted (40mm min) LABEL Note: The carrier tape is compliant to the packaging materials standards for ESD sensitive device, EIA-541 7 4.0 ± ...
Page 8
... Moisture Proof Packaging All HSDL-3211 options are shipped in moisture proof package. Once opened, moisture absorption begins. UNITS IN A SEALED MOISTURE-PROOF PACKAGE IS OPENED (UNSEALED) ENVIRONMENT LESS THAN 30°C, AND LESS THAN NO BAKING YES OPENED LESS IS NECESSARY THAN 72 HOURS PERFORM RECOMMENDED BAKING CONDITIONS Figure 9 ...
Page 9
... The cool down rate, R5, from the liquidus point of the solder to 25° C (77° F) should not exceed 6° C per second maximum. This limitation is necessary to allow the PC board and HSDL-3211 castellations to change dimensions evenly, putting minimal stresses on the HSDL-3211 transceiver. ...
Page 10
Appendix A: SMT Assembly Application Note Solder Pad, Mask and Metal Stencil Aperture STENCIL APERTURE SOLDER MASK Figure 10. Stencil and PCBA. Recommended Land Pattern C L 1.35 MOUNTING CENTER 0.10 1.75 0.60 0.475 1.425 UNIT: mm Figure 11. Stencil ...
Page 11
Recommended Metal Solder Stencil Aperture It is recommended that only a 0.152 mm (0.006 inches 0.127 mm (0.005 inches) thick stencil be used for solder paste printing. This is to ensure adequate printed solder paste volume and no ...
Page 12
Appendix B: PCB Layout Suggestion The following PCB layout guide- lines should be followed to obtain a good PSRR and EM immunity resulting in good electrical performance. Things to note: 1. The ground plane should be continuous under the part, ...
Page 13
... Appendix C: General Application Guide for the HSDL-3211 Description The HSDL-3211, a low-cost and small form factor infrared trans- ceiver, is designed to address the mobile computing market such as PDAs, as well as small-embedded mobile products such as digital cameras and cellular phones fully compliant to IrDA 1.4 low power specification from 9 ...
Page 14
... ROM FOR EMBEDDED APPLICATION PCMCIA CONTROLLER RS232C DRIVER Figure 16. PDA platform. The link distance testing was done using typical HSDL-3211 units with SMC’s FDC37C669 and FDC37N769 Super I/O controllers link distance was demonstrated for SIR and MIR at full power HSDL-3211 ...
Page 15
... Appendix D: Window Designs for HSDL-3211 Optical port dimensions for HSDL-3211 To ensure IrDA compliance, some constraints on the height and width of the window exist. The minimum dimensions ensure that the IrDA cone angles are met without vignetting. The maxi- mum dimensions minimize the effects of stray light ...
Page 16
Module Depth Aperture Width (x, mm) (z) mm Max. 0 8.76 1 9.92 2 11.07 3 12.22 4 13.38 5 14.53 6 15.69 7 16.84 8 18.00 9 19.15 APERTURE WIDTH (X) vs. MODULE DEPTH ...
Page 17
Window Material Almost any plastic material will work as a window material. Polycarbonate is recommended. The surface finish of the plastic should be smooth, without any texture filter dye may be used in the window to make it ...
Page 18
For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. ...