HSDL-3602 Avago Technologies, HSDL-3602 Datasheet
HSDL-3602
Available stocks
Related parts for HSDL-3602
HSDL-3602 Summary of contents
Page 1
... IrDA® Data 1.4 Compliant 4 Mb/s 3V Infrared Transceiver Data Sheet Description The HSDL-3602 is a low pro le infrared transceiver mod- ule that provides interface between logic and IR signals for through-air, serial, half-duplex IR data link. The mod- ule is compliant to IrDA Data Physical Layer Speci ca- tions 1 ...
Page 2
... The HSDL-3602 can be completely shut down to achieve very low power consumption. In the shut down mode, the PIN diode is inactive, thus producing very lit- tle photo-current even under very bright ambient light. The HSDL-3602 also incorporates the capability for adjustable optical power. With two programming pins; ...
Page 3
... Tantalum Notes: 5. CX1 must be placed within 0 the HSDL-3602 to obtain optimum noise immunity "HSDL-3602 Functional Block Diagram" on page assumed that Vled and V the 2 pins are powered by di erent supplies CX2 is applicable for Vled and CX1 for V CX2 on the V line can enhance supply rejection performance ...
Page 4
... Marking Information The HSDL-3602-007/-037 is marked ‘3602YYWW’ on the shield where ‘YY’ indicates the unit’s manufacturing year, and ‘WW’ refers to the work week in which the unit is tested. [7] Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature DC LED Current Peak LED Current ...
Page 5
Recommended Operating Conditions Parameter Symbol Operating Temperature T A Supply Voltage V CC Logic High Input Voltage V IH for TXD, MD0, MD1, and FIR_SEL Logic Low Transmitter V IL Input Voltage LED (Logic High) Current I LEDA Pulse Amplitude ...
Page 6
... Pulse width speci ed is the pulse width of the second 500 kHz carrier pulse received in a data bit. The rst 500 kHz carrier pulse may exceed 2 µs in width, which will not a ect correct demodulation of the data stream. An ASK or DASK system using the HSDL-3602 has been shown to correctly receive all data bits for 9 µ ...
Page 7
TXD "Stuck ON" Protection LED Optical Waveform 7 RXD Output Waveform Receiver Wake Up Time De nition (when MD0 ≠ 1 and MD1 ≠ 0) ...
Page 8
... HSDL-3602-007 and HSDL-3602-037 Package Outline with Dimension and Recommended PC Board Pad Layout 8 ...
Page 9
... HSDL-3602-008 and HSDL-3602-038 Package Outline with Dimension and Recommended PC Board Pad Layout 9 ...
Page 10
... Tape and Reel Dimensions (HSDL-3602-007, -037 Æ1.55 ± 0.05 3 (MAX.) 4.4 A 5.20 ± 0. SECTION A 2.00 ± 0.10 4.00 ± 0.10 Æ1.5 ± 0 8.00 ± 0. 1.75 ± 0.10 5 (MAX.) 11.50 ± 0.10 2 12.50 ± 0.10 12 24.00 ± 0. 0.40 ± 0. 4.25 ± 0.10 SECTION B-B ...
Page 11
... Tape and Reel Dimensions (HSDL-3602-008, -038) 11 ...
Page 12
... Moisture Proof Packaging All HSDL-3602 options are shipped in moisture proof package. Once opened, moisture absorption begins. 12 Baking Conditions If the parts are not stored in dry conditions, they must be baked before prevent damage to the parts. Package Temp. In reels 60°C In bulk 100°C 125° ...
Page 13
... The ∆T/∆time rates are detailed in the following table. The temperatures are measured at the component to printed circuit board connections. In process zone P1, the PC board and HSDL-3602 cas- tellation pins are heated to a temperature of 160°C to activate the ux in the solder paste. The temperature ramp up rate, R1, is limited to 4° ...
Page 14
... Appendix A: HSDL-3602-007/-037 SMT Assembly Application Note 1.0. Solder Pad, Mask, and Metal Solder Stencil Aperture Figure 1. Stencil and PCBA. 1.1. Recommended Land Pattern for HSDL-3602-007/-037 Dim 2.40 b 0.70 c (pitch) 1.10 d 2.35 e 2.80 f 3.13 g 4.31 Figure 2. Top view of land pattern. 14 inches 0.095 0.028 0.043 0.093 ...
Page 15
... It is recommended that 2 ducial cross be placed at mid-length of the pads for unit alignment. Note : Wet/Liquid Photo-Imagineable solder resist/mask is recommended. Figure 3. HSDL-3602-007/-037 PCBA-Adjacent land keep-out and solder mask. 15 inches min. 0.008 0.528 0.185 ...
Page 16
Recommended solder paste/cream volume for castel- lation joints Based on calculation and experiment, the printed sol- der paste volume required per castellation pad is 0.30 cubic mm (based on either no-clean or aqueous solder cream types with typically 60 ...
Page 17
Tolerance for X-axis Alignment of Castellation Misalignment of castellation to the land pad should not exceed 0 approximately half the width of the cas- tellation during placement of the unit. The castellations will completely self-align to the ...
Page 18
... This joint is formed when the printed solder paste volume is adequate, i.e., 0.30 cubic mm and re owed properly. It should be re owed in IR Hot-air convection re ow oven. Direction of board travel does not matter. 4.0. Solder Volume Evaluation and Calculation Geometery of an HSDL-3602-007/-037 solder llet. 18 Picture 5. Good solder joint. ...
Page 19
... Appendix B: HSDL-3602-008/-038 SMT Assembly Application Note 1.0. Solder Pad, Mask, and Metal Solder Stencil Aperture Figure 1. Stencil and PCBA. 1.1. Recommended Land Pattern for HSDL-3602-008/-038 Dim 1.95 b 0.60 c (pitch) 1.10 d 1.60 e 5.70 f 3.80 g 2.40 19 inches 0.077 0.024 0.043 0.063 0.224 0.123 0.170 ...
Page 20
Y-axis Misalignment of Castellation In the Y-direction, the unit does not self-align after sol- der re ow recommended that the unit be placed in line with the ducial mark (mid-length of land pad). This will enable su ...
Page 21
... LED current of 400 mA. Interface to Recommended I/O chips The HSDL-3602’s TXD data input is bu ered to allow for CMOS drive levels. No peaking circuit or capacitor is required. Data rate from 9.6 kb Mb/s is available at the RXD pin. The FIR_SEL pin selects the data rate that is receivable through RXD ...
Page 22
... HSDL-3602 Interoperability with National Semiconduc- tor PC97338VJG SIO Evaluation R eport Introduction The objective of this report is to demonstrate the in- teroperability of the HSDL-3602 IR transceiver IR mod- ule as wireless communication ports at the speed of 2.4 kb Mb/s with NS’s PC97338VJG Super I/O under typical operating conditions. Test Procedures (1) Two PC97338VJG evaluation boards were con- nected to the ISA Bus of two PCs (Pentium 200 MHz) running Microsoft’ ...
Page 23
... Vcc = 3.0 – 3.6 V RLED = 2.2 Ω Optical transmitter pulse width = 125 ns Mode set to full power (ii) Test Result The interoperability test results show that HSDL-3602 IR transceiver can operate ≥ 1.5 meter link distance from 3.6 V with SMC 669/769 at any IrDA 1.1 data rate without error. ...
Page 24
... FDC37C669FR FDC37N769 FDC37C957/8FR HSDL-3602 Interoperability with SMC's Super I Controller 24 IRTX IRRX 204 203 IRMODE 23 21 145 or 190 ...
Page 25
... In the gure below the width of the window the height of the window and Z is the distance from the HSDL-3602 to the back of the window. The distance from the center of the LED lens to the center of the photodiode lens 7.08mm. The equations for com- ...
Page 26
... The depth of the LED image inside the HSDL-3602 8mm. ‘A’ is the required half angle for viewing. For IrDA 0 compliance, the minimum is 15 and the maximum Assuming the thickness of the window to be neg- ligible, the equations result in the following tables and ...
Page 27
... For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries. Data subject to change. Copyright © 2006 Avago Technologies Pte. All rights reserved. ...