MINIASMDC150F/16-2 Tyco Electronics, MINIASMDC150F/16-2 Datasheet - Page 9

• Manufacturer Part Number: MINIASMDC150F/16-2
• Description: TPE / MINI-SMD
• Manufacturer: Tyco Electronics

Specifications of MINIASMDC150F/16-2

• Hold Current: 1.5 Amps
• Trip Current: 2.8 Amps
• Current Rating (max): 100 Amps
• Resistance: 0.11 Ohms
• Maximum Voltage: 16 Volts
• Termination Style: Solder Pad
• Mounting Style: SMD/SMT
• Dimensions: 4.83 mm L x 3.41 mm W x 0.48 mm H
• Package / Case: 1812 (4532 metric)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: RF2160-000

PS400 Test Items and Results (Based on AEC-Q200 Specifi cation)
* Most tested devices meet the load dump test with a peak voltage of 86.5V. However some only meet a reduced peak voltage surge. Contact us if you need more details.
Circuit Protection Products
308 Constitution Drive
Menlo Park, CA USA 94025-1164
Tel : [phone]
Fax : [phone]
PolySwitch, TE (logo) and Tyco Electronics are trademarks of the Tyco Electronics group of companies and its
licensors. Other logos, product and Company names mentioned herein may be trademarks of their respective owners.
All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the
suitability of each product for their application. Tyco Electronics Corporation makes no warranties as to the accuracy
or completeness of the information, and disclaims any liability regarding its use. Tyco Electronics’ only obligations
are those in the Tyco Electronics Standard Terms and Conditions of Sale for this product, and in no case will Tyco
Electronics be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse
of the product. Specifi cations are subject to change without notice. In addition, Tyco Electronics reserves the right
to make changes without notifi cation to Buyer—to materials or processing that do not affect compliance with any
applicable specifi cation.
© 2010 Tyco Electronics Corporation. All rights reserved. RCP0093E.1110
Item
1
4
6
7
8
12
13
14
15
16
17
18
21
22
31
32
33
34
35
Test
Pre & post stress
electrical test
Temperature cycling
Moisture resistance
Biased humidity
Operational life
Resistance to
solvents
Mechanical shock
Vibration
Resistance to
soldering heat
Thermal shock
ESD
Solderability
Board fl ex
Terminal strength
Short circuit fault
current durability
Fault current
durability
End-of-life-mode
verifi cation
Jump start
endurance
Load dump
endurance
Test condition
Passive resistance, TtT, I
-40°C to 85°C
1000 cycles
t = 24 hours/cycle; 10 continuous cycles
Un-powered
1000 hours
85°C ± 5°C/85%RH±5%
Test current: 10% of I
1000 hours
Rated Temp. and tol: 85°C ±2°C
Still air requirement: None
Dist of temp measurement: 4”min
Three solvents.
Immersion
and part damage
Condition: F
Mounting cfg.: per general spec.
5 g’s for 20 min.
12 cycles each of 3 orientations
Test from 10-2000 Hz
Per MIL-STD-202G
Test conditions I, J, K
-40°C to 85°C
Transfer time: 20 sec;
Dwell time: 15 minutes
Medium: Air - Air
15KV air discharge level
260(+0/-5)°C
(Pb free solder paste)
220(+0/-5)°C
(Pb contained solder paste)
Room temperature
V
Room temperature
16V/6 x I
Room temperature
16V/6 x I
Test voltage: 26V
Duty cycle: 1min ±3sec ON, 2 min OFF
3 pulses
Test per ISO7637-2, pulse 5a, 10 times
DC
/200A, (16V for miniASMDC014F)
HOLD
HOLD
brush, 3 cycles, inspection for marking
10 seconds max
10 seconds max
www.circuitprotection.com
www.circuitprotection.com.hk (Chinese)
www.tycoelectronics.com/japan/bu/circuitprotection (Japanese)
HOLD
HOLD
, Pd
Details
Ramp rate 10°C/min
Soak time 5 minutes
In-test measurement: None
Operation condition: Rated Voltage/I
ON-OFF frequency: 15 sec ON 15 sec OFF
Per MIL-STD-202G
METHOD 215K
Peak value 1500g’s half-sine
0.5msec for each duration
Repeat 3 times per direction
Frequency 1: 10 - 40 Hz
Amplitude: ± 0.75 mm
Frequency 2: 40 – 2KHz
Amplitude: 5 g’s peak
Repeat 3 times
24hrs cooling time prior to fi nal measurement
No. of cycles: 300
Test with devices after 8 hours steam aging
Total defl ection: 2.0mm minimum
Defl ection time: 60 (-0/+5) sec.
17.7 N (1.8 Kg) force to the side of a device being
tested for 60sec
5 sec ON, 2 minutes OFF
25 cycles
Min. 5 minutes ON
Min. 10 minutes OFF
5 sec ON, 1 minute OFF
1000 cycles
Test voltage: Us=86.5V/66.5V/46.5V (the two lower
Us values correspond to truncated surge profi les)*
Devices tested under un-tripped status, Ua=13.5V
HOLD
Test Results
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass*