AD5726YRSZ-REEL Analog Devices Inc, AD5726YRSZ-REEL Datasheet - Page 13
![IC,D/A CONVERTER,QUAD,12-BIT,CMOS,SSOP,16PIN](/photos/6/68/66857/rs-16_sml.jpg)
AD5726YRSZ-REEL
Manufacturer Part Number
AD5726YRSZ-REEL
Description
IC,D/A CONVERTER,QUAD,12-BIT,CMOS,SSOP,16PIN
Manufacturer
Analog Devices Inc
Datasheet
1.AD5726YRSZ-REEL.pdf
(20 pages)
Specifications of AD5726YRSZ-REEL
Settling Time
9µs
Number Of Bits
12
Data Interface
Serial
Number Of Converters
4
Voltage Supply Source
Dual ±
Power Dissipation (max)
30mW Unipolar; 240mW Bipolar
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
16-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
AD5726YRSZ-REELTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD5726YRSZ-REEL
Manufacturer:
NXP
Quantity:
1 669
THEORY OF OPERATION
The AD5726 is a quad, 12-bit, serial input, unipolar/bipolar
voltage output DAC. It operates from single-supply voltages of
+5 V to +15 V or dual-supply voltages of ±5 V to ±15 V. The
four outputs are buffered and capable of driving a 2 kΩ load.
Data is written to the AD5726 in a 16-bit word format via a
3-wire serial interface.
DAC ARCHITECTURE
Each of the four DACs is a voltage switched, high impedance
(50 kΩ), R-2R ladder configuration. Each 2R resistor is driven by a
pair of switches that connect the resistor to either V
OUTPUT AMPLIFIERS
The AD5726 features buffered analog voltage outputs capable of
sourcing and sinking up to 5 mA when operating from ±15 V
supplies, eliminating the need for external buffer amplifiers in
most applications while maintaining specified accuracy over the
rated operating conditions. The output amplifiers are short-circuit
protected. The designer should verify that the output load meets
the capabilities of the device, in terms of both output current and
load capacitance. The AD5726 is stable with capacitive loads up
to 2 nF typically. However, any capacitance load increases the
settling time and should be minimized if speed is a concern.
The output stage includes a P-channel MOSFET to pull the
output voltage down to the negative supply. This is very impor-
tant in single-supply systems where V
potential as the negative supply. With no load, the zero-scale
output voltage in these applications is less than 500 μV typically,
or less than 1 LSB when V
current, this voltage increases because of the finite impedance
of the output stage. The effective value of the pull-down resistor
in the output stage is typically 320 Ω. With a 100 kΩ resistor
connected to 5 V, the resulting zero-scale output voltage is
16 mV. Thus, the best single-supply operation is obtained with
the output load connected to ground, so the output stage does
not have to sink current.
Like all amplifiers, the AD5726 output buffers generate voltage
noise, 5 nV/√Hz typically. This is easily reduced by adding a
simple RC low-pass filter on each output.
REFERENCE INPUTS
The two reference inputs of the AD5726 allow a great deal of
flexibility in circuit design. The user must take care, however,
to observe the minimum voltage input levels on V
to maintain the accuracy shown in the data sheet. These input
voltages can be set anywhere across a wide range within the
supplies, but must be a minimum of 2.5 V apart in any case
(see Figure 24). A wide output voltage range can be obtained
with ±5 V references that can be provided by the
shown in Figure 26. Many applications utilize the DACs to
REFP
= 2.5 V. However, when sinking
REFN
usually has the same
AD588
REFP
REFP
and V
or V
as
REFN
REFN
Rev. B | Page 13 of 20
.
synthesize symmetric bipolar waveforms, which require an
accurate, low drift bipolar reference. The AD588 provides both
voltages and needs no external components. Additionally, the
part is trimmed in production for 12-bit accuracy over the full
temperature range without user calibration.
When driving the reference input, it is important to note that
V
of both are code dependent. Many voltage reference products
have limited current sinking capabilities and must be buffered
with an amplifier to drive V
racy. The input, V
For a single 5 V supply, V
must always be at least 2.5 V less than the positive supply to ensure
linearity of the device. For these applications, the
excellent low drift 2.5 V reference. It works well with the AD5726
in a single 5 V system, as shown in Figure 28.
It is recommended that the reference inputs be bypassed with
0.2 μF capacitors when operating with ±10 V references. This
limits the reference bandwidth.
V
The AD5726 uses a DAC switch driver circuit that compensates
for different supplies, reference voltages, and digital code inputs.
This ensures that all DAC ladder switches are always biased
equally, ensuring excellent linearity under all conditions. Thus,
as indicated in the specifications, the V
requires both sourcing and sinking current capability from the
reference voltage source. Many positive voltage references are
intended as current sources only and offer little sinking capability.
The user should consider references such as the AD584, AD586,
AD587, AD588, AD780, and
REFP
REFP
both sinks and sources current, and that the input currents
Input Requirements
V
V
AV
AV
REFN
REFP
DD
SS
+2.5V MIN
+2.5V MIN
0V MIN
Figure 24. Output Voltage Range Programming
0x000
REFN
, however, has no such requirement.
REFP
REFP
is limited to 2.5 V at the most, and
REF43
to maintain overall system accu-
–10V MIN
for such an application.
REFP
0xFFF
input of the AD5726
1 LSB
AD780
AD5726
is an