AD73311LARUZ-RL Analog Devices Inc, AD73311LARUZ-RL Datasheet - Page 16
![SINGLE-CHANNEL AFE I.C.](/photos/1/38/13835/505-20-ssop_sml.jpg)
AD73311LARUZ-RL
Manufacturer Part Number
AD73311LARUZ-RL
Description
SINGLE-CHANNEL AFE I.C.
Manufacturer
Analog Devices Inc
Datasheet
1.AD73311ARZ.pdf
(36 pages)
Specifications of AD73311LARUZ-RL
Number Of Bits
16
Number Of Channels
2
Power (watts)
50mW
Voltage - Supply, Analog
3V
Voltage - Supply, Digital
3V
Package / Case
20-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD73311
OPERATION
Resetting the AD73311
The pin RESET resets all the control registers. All registers
are reset to zero indicating that the default SCLK rate
(DMCLK/8) and sample rate (DMCLK/2048) are at a mini-
mum to ensure that slow speed DSP engines can communicate
effectively. As well as resetting the control registers using the
RESET pin, the device can be reset using the RESET bit (CRA:7)
in Control Register A. Both hardware and software resets re-
quire 4 DMCLK cycles. On reset, DATA/PGM (CRA:0) is set
to 0 (default condition) thus enabling Program Mode. The reset
conditions ensure that the device must be programmed to the
correct settings after power-up or reset. Following a reset, the
SDOFS will be asserted 280 DMCLK cycles after RESET
going high. The data that is output following RESET and dur-
ing Program Mode is random and contains no valid information
until either data or mixed mode is set.
Power Management
The individual functional blocks of the AD73311 can be en-
abled separately by programming the power control register
CRC. It allows certain sections to be powered down if not re-
quired, which adds to the device’s flexibility in that the user
Control
Bit 15
Bit 14
Bits 13–11
Bits 10–8
Bits 7–0
Address (Binary)
000
001
010
011
100
101 to 111
C/D
15
R/W
14
Frame
Control/Data
Read/Write
Device Address
Register Address
Register Data
DEVICE ADDRESS
13
12
Name
CRA
CRB
CRC
CRD
CRE
11
Description
When set high, it signifies a control word in Program or Mixed Program/Data Modes. When
set low, it signifies a data word in Mixed Program/Data Mode or an invalid control word in
Program Mode.
When set low, it tells the device that the data field is to be written to the register selected by
the register field setting provided the address field is zero. When set high, it tells the device
that the selected register is to be written to the data field in the input serial register and that
the new control word is to be output from the device via the serial output.
This 3-bit field holds the address information. Only when this field is zero is a device se-
lected. If the address is not zero, it is decremented and the control word is passed out of
the device via the serial output.
This 3-bit field is used to select one of the five control registers on the AD73311.
This 8-bit field holds the data that is to be written to or read from the selected register
provided the address field is zero.
REGISTER ADDRESS
10
Description
Control Register A
Control Register B
Control Register C
Control Register D
Control Register E
Reserved
Table X. Control Word Description
Table IX. Control Register Map
9
8
need not incur the penalty of having to provide power for a
certain section if it is not necessary to their design. The power
control register provides individual control settings for the major
functional blocks and also a global override that allows all sec-
tions to be powered up by setting the bit. Using this method the
user could, for example, individually enable a certain section,
such as the reference (CRC:5), and disable all others. The glo-
bal power-up (CRC:0) can be used to enable all sections but if
power-down is required using the global control, the reference
will still be enabled, in this case, because its individual bit is set.
Refer to Table XIII for details of the settings of CRC.
Operating Modes
There are five operating modes available on the AD73311. Two
of these—Analog Loop-Back and Digital Loop-Back—are
reserved as diagnostic modes with the other three, Program,
Data and Mixed Program/Data, being available for general
purpose use. The device configuration—register settings—can
be changed only in Program and Mixed Program/Data Modes.
In all modes, transfers of information to or from the device
occur in 16-bit packets, therefore the DSP engine’s SPORT
will be programmed for 16-bit transfers.
7
6
Type
R/W
R/W
R/W
R/W
R/W
5
REGISTER DATA
4
Width
8
8
8
8
8
3
2
Reset Setting (Hex)
0x00
0x00
0x00
0x00
0x00
1
0