AD7568BPZ Analog Devices Inc, AD7568BPZ Datasheet - Page 11
![OCTAL 12-BIT DAC IC](/photos/6/62/66278/505-44-plcc_sml.jpg)
AD7568BPZ
Manufacturer Part Number
AD7568BPZ
Description
OCTAL 12-BIT DAC IC
Manufacturer
Analog Devices Inc
Datasheet
1.AD7568BPZ-REEL.pdf
(12 pages)
Specifications of AD7568BPZ
Rohs Compliant
YES
Settling Time
500ns
Number Of Bits
12
Data Interface
Serial
Number Of Converters
8
Voltage Supply Source
Single Supply
Power Dissipation (max)
17.5mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
44-PLCC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD7568BPZ
Manufacturer:
Analog Devices Inc
Quantity:
135
Company:
Part Number:
AD7568BPZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD7568BPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7568BPZ-REEL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
REV. B
In Figure 21, LDAC and CLR are controlled by the PC6 and
PC5 port outputs. As with the 80C51, each DAC of the
AD7568 can be updated after each two-byte transfer, or else all
DACs can be simultaneously updated.
AD7568–ADSP-2101 Interface
Figure 22 shows a serial interface between the AD7568 and the
ADSP-2101 digital signal processor. The ADSP-2101 may be
set up to operate in the SPORT Transmit Normal Internal
Framing Mode. The following ADSP-2101 conditions are rec-
ommended: Internal SCLK; Active High Framing Signal; 16-bit
word length. Transmission is initiated by writing a word to the
TX register after the SPORT has been enabled. The data is then
clocked out on every rising edge of SCLK after TFS goes low.
TFS stays low until the next data transfer.
AD7568–TMS320C25 Interface
Figure 23 shows an interface circuit for the TMS320C25
digital signal processor. The data on the DX pin is clocked
out of the processor’s Transmit Shift Register by the CLKX
signal. Sixteen-bit transmit format should be chosen by setting
the FO bit in the ST1 register to 0. The transmit operation be-
gins when data is written into the data transmit register of the
TMS320C25. This data will be transmitted when the FSX line
goes low while CLKX is high or going high. The data, starting
Figure 22. AD7568 to ADSP-2101 Interface
Figure 21. AD7568 to 68HC11 Interface
*ADDITIONAL PINS OMITTED FOR CLARITY
*ADDITIONAL PINS OMITTED FOR CLARITY
ADSP-2101*
68HC11*
MOSI
SCK
PC5
PC6
PC7
SCLK
TFS
FO
DT
+5V
CLR
LDAC
CLKIN
SDIN
FSIN
CLR
LDAC
SDIN
CLKIN
AD7568*
FSIN
AD7568*
–11–
with the MSB, is then shifted out to the DX pin on the rising
edge of CLKX. When all bits have been transmitted, the user
can update the DAC outputs by bringing the XF output flag low.
Multiple DAC Systems
If there are only two AD7568s in a system, there is a simple way
of programming each. This is shown in Figure 24. If the user
wishes to program one of the DACs in the first AD7568, then
DB3 of the serial bit stream should be set to 0, to correspond to
the state of the A0 pin on that device. If the user wishes to pro-
gram a DAC in the second AD7568, then DB3 should be set to
1, to correspond to A0 on that device.
Figure 24. Interfacing ADSP-2101 to Two AD7568s
Figure 23. AD7568 to TMS320C25 Interface
*ADDITIONAL PINS OMITTED FOR CLARITY
*ADDITIONAL PINS OMITTED FOR CLARITY
TMS320C25*
ADSP-2101*
CLKX
SCLK
FSX
TFS
FO
XF
DX
DT
GENERATION
CLOCK
+5V
+5V
+5V
CLR
LDAC
SDIN
A0
CLR
LDAC
FSIN
SDIN
CLKIN
LDAC
FSIN
SDIN
CLKIN
A0
CLR
FSIN
CLKIN
AD7568*
AD7568*
AD7568*
AD7568