AD8607AR Analog Devices Inc, AD8607AR Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD8607AR
Manufacturer Part Number
AD8607AR
Description
DUAL, PRECISION CMOS RAIL-RAIL OP AMP
Manufacturer
Analog Devices Inc
Datasheet
1.AD8607ARMZ-REEL.pdf
(16 pages)
Specifications of AD8607AR
Rohs Compliant
NO
Rohs Status
RoHS non-compliant
Amplifier Type
General Purpose
Number Of Circuits
2
Output Type
Rail-to-Rail
Slew Rate
0.1 V/µs
Gain Bandwidth Product
400kHz
Current - Input Bias
0.2pA
Voltage - Input Offset
12µV
Current - Supply
40µA
Current - Output / Channel
70mA
Voltage - Supply, Single/dual (±)
1.8 V ~ 5 V, ±0.9 V ~ 2.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
-3db Bandwidth
-
Lead Free Status / RoHS Status
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD8607AR
Manufacturer:
SHARP
Quantity:
4 218
Part Number:
AD8607AR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD8607AR-
Manufacturer:
AVID
Quantity:
1 440
Part Number:
AD8607AR-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD8607AR-REEL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD8607ARM
Manufacturer:
AD
Quantity:
2 000
Part Number:
AD8607ARM-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD8607ARMZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD8607ARMZ-REEL
Manufacturer:
AD
Quantity:
14 524
Company:
Part Number:
AD8607ARZ
Manufacturer:
ADI
Quantity:
7 500
AD8603/AD8607/AD8609
APPLICATIONS
NO PHASE REVERSAL
The AD8603/AD8607/AD8609 do not exhibit phase inversion
even when the input voltage exceeds the maximum input
common-mode voltage. Phase reversal can cause permanent
damage to the amplifier, resulting in system lockups. The
AD8603/AD8607/AD8609 can handle voltages of up to 1 V
over the supply.
INPUT OVERVOLTAGE PROTECTION
If a voltage 1 V higher than the supplies is applied at either
input, the use of a limiting series resistor is recommended. If
both inputs are used, each one should be protected with a
series resistor.
To ensure good protection, the current should be limited to a
maximum of 5 mA. The value of the limiting resistor can be
determined from the following equation:
DRIVING CAPACITIVE LOADS
The AD8603/AD8607/AD8609 are capable of driving large
capacitive loads without oscillating. Figure 42 shows the output
of the AD8603/AD8607/AD8609 in response to a 100 mV input
signal, with a 2 nF capacitive load.
Although it is configured in positive unity gain (the worst case),
the AD8603 shows less than 20% overshoot. Simple additional
circuitry can eliminate ringing and overshoot.
One technique is the snubber network, which consists of a
series RC and a resistive load (see Figure 43). With the snubber
in place, the AD8603/AD8607/AD8609 are capable of driving
capacitive loads of 2 nF with no ringing and less than 3%
overshoot.
(V
IN
− V
S
)/(R
S
+ 200 Ω) ≤ 5 mA
Figure 41. No Phase Response
V
IN
TIME (4µs/DIV)
V
OUT
V
V
A
R
S
IN
V
L
= ±2.5V
= 1
= 10kΩ
= 6V p-p
Rev. C | Page 12 of 16
The use of the snubber circuit is usually recommended for unity
gain configurations. Higher gain configurations help improve
the stability of the circuit. Figure 44 shows the same output
response with the snubber in place.
Optimum values for R
Table 5 lists a few starting values.
Table 5. Optimum Values for the Snubber Network
C
100 to ~500
1500
1600 to ~2000
L
Figure 42. Output Response to a 2 nF Capacitive Load, Without Snubber
(pF)
Figure 44. Output Response to a 2 nF Capacitive Load with Snubber
200mV
Figure 43. Snubber Network
S
R
500
100
400
+
–
and C
S
(Ω)
V
V
V–
V+
EE
CC
S
are determined empirically;
47pF
150Ω
C
R
S
S
C
V
V
C
R
V
V
C
R
R
C
C
330
L
680
100
S
IN
L
L
SY
IN
L
L
S
S
S
= ±0.9V
= 2nF
= 10kΩ
= 100mV
= 2nF
= 10kΩ
= 150Ω
= 470pF
= 100mV
= ±0.9V
(pF)