AD9216BCPZ-80 Analog Devices Inc, AD9216BCPZ-80 Datasheet - Page 12
![IC,A/D CONVERTER,DUAL,10-BIT,CMOS,LLCC,64PIN](/photos/6/50/65021/505-64-lfcsp_sml.jpg)
AD9216BCPZ-80
Manufacturer Part Number
AD9216BCPZ-80
Description
IC,A/D CONVERTER,DUAL,10-BIT,CMOS,LLCC,64PIN
Manufacturer
Analog Devices Inc
Datasheet
1.AD9216BCPZ-65.pdf
(40 pages)
Specifications of AD9216BCPZ-80
Number Of Bits
10
Sampling Rate (per Second)
80M
Data Interface
Parallel
Number Of Converters
2
Power Dissipation (max)
255mW
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LFCSP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AD9216-80PCBZ - BOARD EVAL FOR AD9216 80MSPSAD9216-105PCBZ - BOARD EVAL FOR AD9216 105MSPS
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD9216
Noise (for Any Range within the ADC)
This value includes both thermal and quantization noise.
where:
Z is the input impedance.
FS is the full scale of the device for the frequency in question.
SNR is the value for the particular input level.
Signal is the signal level within the ADC reported in dB below
full scale.
Power Supply Rejection Ratio
The specification shows the maximum change in full scale
from the value with the supply at the minimum limit to the
value with the supply at its maximum limit.
Signal-to-Noise and Distortion (SINAD)
The ratio of the rms signal amplitude (set 1 dB below full scale)
to the rms value of the sum of all other spectral components,
including harmonics, but excluding dc.
Signal-to-Noise Ratio (without Harmonics)
The ratio of the rms signal amplitude (set at 1 dB below
full scale) to the rms value of the sum of all other spectral
components, excluding the first seven harmonics and dc.
Spurious-Free Dynamic Range (SFDR)
The ratio of the rms signal amplitude to the rms value of
the peak spurious spectral component. The peak spurious
component may or may not be a harmonic. It also may be
reported in dBc (that is, degrades as signal level is lowered)
or dBFS (that is, always related back to converter full scale).
V
noise
=
Z
×
0
.001
×
10
⎛
⎜ ⎜
⎝
FS
dBm
−
SNR
10
dBc
−
Signal
dBFS
⎞
⎟ ⎟
⎠
Rev. A | Page 12 of 40
Two-Tone Intermodulation Distortion Rejection
The ratio of the rms value of either input tone to the rms value
of the worst third-order intermodulation product, in dBc.
Two-Tone SFDR
The ratio of the rms value of either input tone to the rms value
of the peak spurious component. The peak spurious
component may or may not be an IMD product. It also may be
reported in dBc (that is, degrades as signal level is lowered) or
in dBFS (that is, always relates back to converter full scale).
Worst Other Spur
The ratio of the rms signal amplitude to the rms value of the
worst spurious component (excluding the second and third
harmonic), reported in dBc.
Transient Response Time
The time it takes for the ADC to reacquire the analog input
after a transient from 10% above negative full scale to 10%
below positive full scale.
Out-of-Range Recovery Time
The time it takes for the ADC to reacquire the analog input
after a transient from 10% above positive full scale to 10% above
negative full scale, or from 10% below negative full scale to 10%
below positive full scale.