AD9223ARSZ Analog Devices Inc, AD9223ARSZ Datasheet - Page 18
![12-Bit, 1.5/3.0/10 MSPS ADC](/photos/6/60/66033/505-28-ssop_sml.jpg)
AD9223ARSZ
Manufacturer Part Number
AD9223ARSZ
Description
12-Bit, 1.5/3.0/10 MSPS ADC
Manufacturer
Analog Devices Inc
Specifications of AD9223ARSZ
Number Of Bits
12
Sampling Rate (per Second)
3M
Data Interface
Parallel
Number Of Converters
7
Power Dissipation (max)
130mW
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-SSOP (0.200", 5.30mm Width)
Number Of Elements
1
Resolution
12Bit
Architecture
Pipelined
Sample Rate
3MSPS
Input Polarity
Unipolar
Input Type
Voltage
Rated Input Volt
±1/±2.5V
Differential Input
Yes
Power Supply Requirement
Analog and Digital
Single Supply Voltage (typ)
5V
Single Supply Voltage (min)
4.75V
Single Supply Voltage (max)
5.25V
Dual Supply Voltage (typ)
Not RequiredV
Dual Supply Voltage (min)
Not RequiredV
Dual Supply Voltage (max)
Not RequiredV
Power Dissipation
130mW
Differential Linearity Error
±0.75LSB
Integral Nonlinearity Error
±1.25LSB
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
28
Package Type
SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AD9223-EB - BOARD EVAL FOR AD9223
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD9223ARSZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD9221/AD9223/AD9220
Figure 19 shows the schematic of the suggested transformer
circuit. The circuit uses a Mini-Circuits RF transformer, model
#T4-6T, which has an impedance ratio of 4 (turns ratio of 2).
The schematic assumes that the signal source has a 50 Ω source
impedance. The 1:4 impedance ratio requires the 200 Ω sec-
ondary termination for optimum power transfer and VSWR.
The center tap of the transformer provides a convenient means
of level shifting the input signal to a desired common-mode
voltage. Optimum performance can be realized when the center
tap is tied to CML of the AD9221/AD9223/AD9220, which is
the common-mode bias level of the internal SHA.
Transformers with other turns ratios may also be selected to
optimize the performance of a given application. For example, a
given input signal source or amplifier may realize an improve-
ment in distortion performance at reduced output power levels
and signal swings. Therefore, selecting a transformer with a
higher impedance ratio (e.g., Mini-Circuits T16-6T with a 1:16
impedance ratio) effectively “steps up” the signal level, thus
further reducing the driving requirements of the signal source.
Referring to Figure 19, a series resistor, R
C
the secondary of the transformer. The values of 33 Ω and 15 pF
were selected to specifically optimize both the THD and SNR
performance of the A/D. R
tion from transients at the A/D inputs reflected back through the
primary of the transformer.
The AD9221/AD9223/AD9220 can be easily configured for
either a 2 V p-p input span or 5.0 V p-p input span by setting
the internal reference (see Table II). Other input spans can be
realized with two external gain setting resistors as shown in
S
, were inserted between the AD9221/AD9223/AD9220 and
Figure 18. AD9221/AD9223/AD9220 SFDR vs. Input
Frequency (V
A
IN
= –0.5 dB)
–55
–65
–75
–85
–95
49.9
Figure 19. Transformer Coupled Input
1
MINI-CIRCUITS
T4-1
CM
= 2.5 V, 2 V p-p Input Span,
AD9221
FREQUENCY – MHz
200
S
and C
33
33
R
R
S
S
10
AD9223
S
help provide some isola-
C
15pF
0.1 F
C
15pF
S
S
S
, and shunt capacitor,
AD9220
VINB
VINA
CML
AD9221/
AD9223/
AD9220
100
–18–
Figure 23 of this data sheet. Figure 20 demonstrates how both
spans of the AD9220 achieve the high degree of linearity and
SFDR over a wide range of amplitudes required by the most
demanding communication applications. Similar performance is
achievable with the AD9221 and AD9223 at their correspond-
ing Nyquist frequency.
Figure 20 also reveals a noteworthy difference in the SFDR and
SNR performance of the AD9220 between the 2 V p-p and 5 V p-p
input span options. First, the SNR performance improves by 2 dB
with a 5.0 V p-p input span due to the increase in dynamic
range. Second, the SFDR performance of the AD9220 will
improve for input signals below approximately –6.0 dBFS. A 3 dB
to 5 dB improvement was typically realized for input signal levels
between –6.0 dBFS and –36 dBFS. This improvement in SNR
and SFDR for a 5.0 V p-p span may be advantageous for com-
munication systems that have additional margin or headroom
to minimize clipping of the ADC.
REFERENCE CONFIGURATIONS
The figures associated with this section on internal and external
reference operation do not show recommended matching series resistors
for VINA and VINB for the purpose of simplicity. Please refer to the
Driving the Analog Inputs, Introduction section for a discussion of
this topic. Also, the figures do not show the decoupling network asso-
ciated with the CAPT and CAPB pins. Please refer to the Reference
Operation section for a discussion of the internal reference circuitry
and the recommended decoupling network shown in Figure 10.
USING THE INTERNAL REFERENCE
Single-Ended Input with 0 to 2
Figure 21 shows how to connect the AD9221/AD9223/AD9220
for a 0 V to 2 V or 0 V to 5 V input range via pin strapping the
SENSE pin. An intermediate input range of 0 to 2 × VREF can
be established using the resistor programmable configuration in
Figure 23 and connecting VREF to VINB.
In either case, both the common-mode voltage and input span
are directly dependent on the value of VREF. More specifically,
the common-mode voltage is equal to VREF while the input
span is equal to 2 × VREF. Thus, the valid input range extends
from 0 to 2 × VREF. When VINA is ≤ 0 V, the digital output
will be 000 Hex; when VINA is ≥ 2 × VREF, the digital output
will be FFF Hex.
Figure 20. AD9220 SFDR, SNR vs. Input Amplitude
(f
IN
= 5 MHz, f
90
80
70
60
50
40
30
20
–50
CLK
–40
= 10 MSPS, V
SFDR – 2.0V p-p
INPUT AMPLITUDE – dBFS
SFDR – 5.0V p-p
–30
SNR – 5.0V p-p
VREF Range
–20
CM
SNR – 2.0V p-p
= 2.5 V, Differential)
–10
0
REV. E