AD9251BCPZ-65 Analog Devices Inc, AD9251BCPZ-65 Datasheet - Page 27
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9251BCPZ-65
Manufacturer Part Number
AD9251BCPZ-65
Description
14 BIT DUAL 65 Msps Low Power ADC
Manufacturer
Analog Devices Inc
Datasheet
1.AD9251BCPZRL7-20.pdf
(36 pages)
Specifications of AD9251BCPZ-65
Number Of Bits
14
Sampling Rate (per Second)
65M
Data Interface
Serial, SPI™
Number Of Converters
2
Power Dissipation (max)
146.5mW
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LFCSP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD9251BCPZ-65
Manufacturer:
ADI
Quantity:
100
Part Number:
AD9251BCPZ-65
Manufacturer:
ADI/亚德诺
Quantity:
20 000
DIGITAL OUTPUTS
The AD9251 output drivers can be configured to interface with
1.8 V to 3.3 V CMOS logic families. Output data can also be
multiplexed onto a single output bus to reduce the total number of
traces required.
The CMOS output drivers are sized to provide sufficient output
current to drive a wide variety of logic families. However, large
drive currents tend to cause current glitches on the supplies and
may affect converter performance.
Applications requiring the ADC to drive large capacitive loads
or large fanouts may require external buffers or latches.
The output data format can be selected to be either offset binary
or twos complement by setting the SCLK/DFS pin when operating
in the external pin mode (see Table 11).
As detailed in the
Speed ADCs via SPI, the data format can be selected for offset
binary, twos complement, or gray code when using the SPI control.
Table 11. SCLK/DFS Mode Selection (External Pin Mode)
Voltage at Pin
AGND
DRVDD
Digital Output Enable Function (OEB)
The AD9251 has a flexible three-state ability for the digital
output pins. The three-state mode is enabled using the OEB pin
or through the SPI interface. If the OEB pin is low, the output
Table 12. Output Data Format
Input (V)
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
Offset binary (default)
Twos complement
SCLK/DFS
AN-877
Condition (V)
< −VREF − 0.5 LSB
= −VREF
= 0
= +VREF − 1.0 LSB
> +VREF − 0.5 LSB
Application Note, Interfacing to High
SDIO/DCS
DCS disabled
DCS enabled (default)
Offset Binary Output Mode
00 0000 0000 0000
00 0000 0000 0000
10 0000 0000 0000
11 1111 1111 1111
11 1111 1111 1111
Rev. A | Page 27 of 36
data drivers and DCOs are enabled. If the OEB pin is high, the
output data drivers and DCOs are placed in a high impedance
state. This OEB function is not intended for rapid access to the
data bus. Note that OEB is referenced to the digital output
driver supply (DRVDD) and should not exceed that supply
voltage.
When using the SPI interface, the data outputs and DCO of
each channel can be independently three-stated by using the
output disable (OEB) bit (Bit 4) in Register 0x14.
TIMING
The AD9251 provides latched data with a pipeline delay of
9 clock cycles. Data outputs are available one propagation delay
(t
Minimize the length of the output data lines and loads placed
on them to reduce transients within the AD9251. These
transients can degrade converter dynamic performance.
The lowest typical conversion rate of the AD9251 is 3 MSPS. At
clock rates below 3 MSPS, dynamic performance can degrade.
Data Clock Output (DCO)
The AD9251 provides two data clock output (DCO) signals
intended for capturing the data in an external register. The CMOS
data outputs are valid on the rising edge of the DCO, unless the
DCO clock polarity has been changed via the SPI. See Figure 2
and Figure 3 for a graphical timing description.
PD
) after the rising edge of the clock signal.
Twos Complement Mode
10 0000 0000 0000
10 0000 0000 0000
00 0000 0000 0000
01 1111 1111 1111
01 1111 1111 1111
AD9251
OR
1
0
0
0
1