ADE7518ASTZF16-RL Analog Devices Inc, ADE7518ASTZF16-RL Datasheet - Page 103
![1-Phase Energy Meter IC](/photos/6/60/66065/505-64-lqfp_sml.jpg)
ADE7518ASTZF16-RL
Manufacturer Part Number
ADE7518ASTZF16-RL
Description
1-Phase Energy Meter IC
Manufacturer
Analog Devices Inc
Datasheet
1.ADE7518ASTZF16.pdf
(128 pages)
Specifications of ADE7518ASTZF16-RL
Applications
Energy Measurement
Core Processor
8052
Program Memory Type
FLASH (16 kB)
Controller Series
ADE75xx
Ram Size
512 x 8
Interface
I²C, SPI, UART
Number Of I /o
20
Voltage - Supply
3.135 V ~ 3.465 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADE7518ASTZF16-RL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
READ AND WRITE OPERATIONS
Writing to the RTC Registers
The RTC circuitry runs off a 32.768 kHz clock. The timekeeping
registers, Hundredths of a Second Counter SFR (HTHSEC, 0xA2),
Seconds Counter SFR (SEC, 0xA3), Minutes Counter SFR (MIN,
0xA4), and Hours Counter SFR (HOUR, 0xA5), are updated
with a 32.768 kHz clock. However, the RTC Configuration SFR
(TIMECON, 0xA1) and Alarm Interval SFR (INTVAL, 0xA6)
are updated with a 128 Hz clock. It takes up to two 128 Hz clock
cycles from when the MCU writes to the TIMECON SFR or the
INTVAL SFR until there is a successful update in the RTC.
To protect the RTC timekeeping registers from runaway code,
a key must be written to the Key SFR (KYREG, 0xC1), which is
described in Table 105, to obtain write access to the HTHSEC,
SEC, MIN, and HOUR SFRs. KYREG should be set to 0xEA to
unlock the timekeeping registers and reset to 0 after a timekeeping
register is written to. The RTC registers can be written to using
the following 8052 assembly code:
MOV
CALL
…
UpdateRTC:
Reading the RTC Counter SFRs
The RTC cannot be stopped to read the current time because
stopping the RTC introduces an error in its timekeeping.
Therefore, the RTC is read on the fly, and the counter registers
must be checked for overflow. This can be accomplished
through the following 8052 assembly code:
ReadAgain:
Bank 0
MOV
MOV
MOV
MOV
MOV
MOV
MOV
RET
MOV
MOV
MOV
MOV
MOV
CJNE A, 00h, ReadAgain ; 00h is R0 in
RTCKey,#0EAh
UpdateRTC
KYREG,RTCKey
SEC,#30
KYREG,RTCKey
MIN,#05
KYREG,RTCKey
HOUR,#04
KYREG,#00h
R0,HTHSEC
R1,SEC
R2,MIN
R3,HOUR
A,HTHSEC
; using Bank 0
Rev. 0 | Page 103 of 128
RTC MODES
The RTC can be configured in a 24-hour mode or a 256-hour
mode. A midnight event is generated when the RTC hour
counter rolls over from 23 to 0 or 255 to 0, depending on
whether the TFH bit is set in the RTC Configuration SFR
(TIMECON, 0xA1). The midnight event sets the MIDNIGHT
flag in the TIMECON SFR, and a pending RTC interrupt is
created. The RTC midnight event wakes the 8052 MCU core if
the MCU is asleep in PSM2 when the midnight event occurs.
In the 24-hour mode, the midnight event is generated once a
day at midnight. The 24-hour mode is useful for updating a
software calendar to keep track of the current day. The 256-hour
mode results in power savings during extended operation in
PSM2 because the MCU core wakes up less frequently.
RTC INTERRUPTS
The RTC midnight interrupt and alarm interrupt are enabled by
setting the ETI bit in the Interrupt Enable and Priority 2 SFR
(IEIP2, 0xA9). When a midnight or alarm event occurs, a pending
RTC interrupt is generated. If the RTC interrupt is enabled, the
program vectors to the RTC interrupt address and the pending
interrupt is cleared. If the RTC interrupt is disabled, the RTC
interrupt remains pending until the RTC interrupt is enabled.
The program then vectors to the RTC interrupt address.
The MIDNIGHT flag and ALARM flag are set when the mid-
night event and alarm event occur, respectively. The user should
manage these flags to keep track of which event caused an RTC
interrupt by servicing the event and clearing the appropriate
flag in the RTC interrupt servicing routine.
Note that if the ADE7518 is awakened by an RTC event, either
by the MIDNIGHT event or the ALARM event, the pending
RTC interrupt must be serviced before the device can go back
to sleep again. The ADE7518 keeps waking up until this inter-
rupt has been serviced.
Interval Timer Alarm
The RTC can be used as an interval timer. When the interval timer
is enabled by setting the ITEN bit in the RTC Configuration SFR
(TIMECON, 0xA1), the interval timer clock source selected by
the ITS1 and ITS0 bits is passed through an 8-bit counter. This
counter increments on every interval timer clock pulse until it is
equal to the value in the Alarm Interval SFR (INTVAL, 0xA6).
Then, an alarm event is generated, setting the ALARM flag and
creating a pending RTC interrupt. If the SIT bit in the RTC
Configuration SFR (TIMECON, 0xA1) is cleared, the 8-bit
counter is also cleared and starts counting again. If the SIT bit is
set, the 8-bit counter is held in reset after the alarm occurs.
ADE7518