ADF4360-7BCPRL7 Analog Devices Inc, ADF4360-7BCPRL7 Datasheet - Page 4

• Manufacturer Part Number: ADF4360-7BCPRL7
• Description: IC,FREQUENCY SYNTHESIZER,BICMOS,LLCC,24PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Type: Fanout Distribution, Integer N Synthesizer (RF)r

Specifications of ADF4360-7BCPRL7

• Rohs Status: RoHS non-compliant
• Pll: Yes
• Input: CMOS
• Output: Clock
• Number Of Circuits: 1
• Ratio - Input:output: 1:2
• Differential - Input:output: No/No
• Frequency - Max: 1.8GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-LFCSP
• Frequency-max: 1.8GHz
• For Use With: EVAL-ADF4360-7EBZ1 - BOARD EVALUATION FOR ADF4360-7

ADF4360-7
Parameter
RF OUTPUT CHARACTERISTICS
NOISE CHARACTERISTIC
1
2
3
4
5
6
7
8
9
10
11
12
13
Operating temperature range is –40°C to +85°C.
Guaranteed by design. Sample tested to ensure compliance.
I
T
Unless otherwise stated, these characteristics are guaranteed for VCO core power = 5 mA. L1, L2 = 13 nH, 470 Ω resistors to GND in parallel with L1, L2.
Jumping from 490 MHz to 585 MHz. PFD frequency = 200 kHz; loop bandwidth = 10 kHz.
Using 50 Ω resistors to V
The noise of the VCO is measured in open-loop conditions.
The synthesizer phase-noise floor is estimated by measuring the in-band phase noise at the output of the VCO and subtracting 20 log N (where N is the N divider value).
CP
The phase noise is measured with the EVAL-ADF4360-xEB1 Evaluation Board and the HP 8562E Spectrum Analyzer. The Spectrum Analyzer provides the REF
f
f
The spurious signals are measured with the EVAL-ADF4360-xEB1 Evaluation Board and the HP 8562E Spectrum Analyzer. The Spectrum Analyzer provides the REF
for the synthesizer; f
synthesizer; offset frequency = 1 kHz.
A
REFIN
REFIN
Maximum VCO Output Frequency
Minimum VCO Output Frequency
VCO Output Frequency
VCO Frequency Range
VCO Sensitivity
Lock Time
Frequency Pushing (Open Loop)
Frequency Pulling (Open Loop)
Harmonic Content (Second)
Harmonic Content (Third)
Output Power
Output Power Variation
VCO Tuning Range
VCO Phase-Noise Performance
Synthesizer Phase-Noise Floor
In-Band Phase Noise
RMS Integrated Phase Error
Spurious Signals due to PFD
Level of Unlocked Signal with
= 25°C; AV
is internally modified to maintain constant loop gain over the frequency range.
Frequency
MTLD Enabled
= 10 MHz; f
= 10 MHz; f
DD
6
= DV
PFD
PFD
11, 13
5, 7
= 200 kHz; N = 2500; loop B/W = 10 kHz.
= 1 MHz; N = 500; loop B/W = 25 kHz.
DD
REFOUT
= V
VCO
10, 11
VCO
= 10 MHz @ 0 dBm.
, into a 50 Ω load. For tuned loads, see the Output M
5
= 3.3 V; P = 32.
12
5
9
8
490/585
1.25/2.5
B Version
1800
350
1.2
12
400
6
15
−19
−9
−14/−5
±3
−116
−138
−144
−148
−172
−163
−147
−92
0.3
−70
−44
MHz min/max
V min/max
Unit
MHz
MHz
Ratio
MHz/V typ
µs typ
MHz/V typ
kHz typ
dBc typ
dBc typ
dBm typ
dB typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
Degrees typ
dBc typ
dBm typ
Rev. A | Page 4 of 28
atching
section.
Conditions/Comments
I
Inductance Value section.
L1, L2 = 13 nH. See the Choosing the Correct Inductance Value
section for other frequency values.
F
L1, L2 = 13 nH. See the Choosing the Correct Inductance Value
section for other sensitivity values.
To within 10 Hz of final frequency.
Into 2.00 VSWR load.
Programmable in 3 dB steps. See Table 7.
For tuned loads, see Output Matching section.
@ 100 kHz offset from carrier.
@ 1 MHz offset from carrier.
@ 3 MHz offset from carrier.
@ 10 MHz offset from carrier.
@ 25 kHz PFD frequency.
@ 200 kHz PFD frequency.
@ 8 MHz PFD frequency.
@ 1 kHz offset from carrier.
100 Hz to 100 kHz.
CORE
MAX
/F
= 5 mA. Depending on L. See the Choosing the Correct
MIN
IN
for the
IN