ADSP-2185MBSTZ-266 Analog Devices Inc, ADSP-2185MBSTZ-266 Datasheet - Page 15

• Manufacturer Part Number: ADSP-2185MBSTZ-266
• Description: 75mhz 16k/16k 2.5v LQFP
• Manufacturer: Analog Devices Inc
• Series: ADSP-21xxr
• Type: Fixed Pointr

Specifications of ADSP-2185MBSTZ-266

• Interface: Host Interface, Serial Port
• Clock Rate: 66MHz
• Non-volatile Memory: External
• On-chip Ram: 80kB
• Voltage - I/o: 3.30V
• Voltage - Core: 2.50V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LQFP
• Package: 100LQFP
• Numeric And Arithmetic Format: Fixed-Point
• Maximum Speed: 66 MHz
• Ram Size: 80 KB
• Device Million Instructions Per Second: 66 MIPS
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ADSP-2185MBSTZ266

The BDMA overlay bits specify the OVLAY memory blocks to
be accessed for internal memory. For ADSP-2185M, set to zero
BDMA overlay bits in BDMA control register.
The BMWAIT field, which has 4 bits on ADSP-2185M, allows
selection up to 15 wait states for BDMA transfers.
Internal Memory DMA Port (IDMA Port; Host Memory
Mode)
The IDMA Port provides an efficient means of communication
between a host system and the ADSP-2185M. The port is used
to access the on-chip program memory and data memory of the
DSP with only one DSP cycle per word overhead. The IDMA
port cannot, however, be used to write to the DSP’s memory-
mapped control registers. A typical IDMA transfer process is
described as follows:
1. Host starts IDMA transfer
2. Host checks IACK control line to see if the DSP is busy
3. Host uses IS and IAL control lines to latch either the DMA
4. Host uses IS and IRD (or IWR) to read (or write) DSP inter-
5. Host checks IACK line to see if the DSP has completed the
6. Host ends IDMA transfer.
The IDMA port has a 16-bit multiplexed address and data bus
and supports 24-bit program memory. The IDMA port is com-
pletely asynchronous and can be written while the ADSP-2185M
is operating at full speed.
The DSP memory address is latched and then automatically incre-
mented after each IDMA transaction. An external device can
therefore access a block of sequentially addressed memory by
specifying only the starting address of the block. This increases
throughput as the address does not have to be sent for each
memory access.
IDMA Port access occurs in two phases. The first is the IDMA
Address Latch cycle. When the acknowledge is asserted, a 14-bit
address and 1-bit destination type can be driven onto the bus by
an external device. The address specifies an on-chip memory
location, the destination type specifies whether it is a DM or
PM access. The falling edge of the IDMA address latch signal
(IAL) or the missing edge of the IDMA select signal (IS) latches
this value into the IDMAA register.
Once the address is stored, data can be read from, or written to,
the ADSP-2185M’s on-chip memory. Asserting the select line
(IS) and the appropriate read or write line (IRD and IWR
respectively) signals the ADSP-2185M that a particular transac-
tion is required. In either case, there is a one-processor-cycle
delay for synchronization. The memory access consumes one
additional processor cycle.
Once an access has occurred, the latched address is automati-
cally incremented, and another access can occur.
starting address (IDMAA) or the PM/DM OVLAY selection
into the DSP’s IDMA control registers. If Bit 15 = 1, the
value of bits 7:0 represent the IDMA overlay: bits 14:8 must
be set to 0. If Bit 15 = 0, the value of Bits 13:0 represent the
starting address of internal memory to be accessed and
Bit 14 reflects PM or DM for access. For ADSP-2185M,
IDDMOVLAY and IDPMOVLAY bits in IDMA overlay
register should be set to zero.
nal memory (PM or DM).
previous IDMA operation.
Through the IDMAA register, the DSP can also specify the
starting address and data format for DMA operation. Asserting
the IDMA port select (IS) and address latch enable (IAL) directs
the ADSP-2185M to write the address onto the IAD0–14 bus
into the IDMA Control Register. If Bit 15 is set to 0, IDMA
latches the address. If Bit 15 is set to 1, IDMA latches into the
OVLAY register. This register, shown below, is memory mapped
at address DM (0x3FE0). Note that the latched address (IDMAA)
cannot be read back by the host. When Bit 14 in 0x3FE7 is set
to 1, timing in Figure 31 applies for short reads. When Bit 14
in 0x3FE7 is set to zero, short reads use the timing shown in Fig-
ure 32. For ADSP-2185M, IDDMOVLAY and IDPMOVLAY
bits in IDMA overlay register should be set to zero.
Refer to the following figures for more information on IDMA
and DMA memory maps.
Bootstrap Loading (Booting)
The ADSP-2185M has two mechanisms to allow automatic load-
ing of the internal program memory after reset. The method for
booting is controlled by the Mode A, B, and C configuration bits.
When the MODE pins specify BDMA booting, the ADSP-2185M
initiates a BDMA boot sequence when reset is released.
The BDMA interface is set up during reset to the following
defaults when BDMA booting is specified: the BDIR, BMPAGE,
BIAD, and BEAD registers are set to 0, the BTYPE register is
set to 0 to specify program memory 24-bit words, and the
BWCOUNT register is set to 32. This causes 32 words of
on-chip program memory to be loaded from byte memory.
NOTES: RESERVED BITS ARE SHOWN ON A GRAY FIELD. THESE BITS
ALWAYS
ACCESSIBLE
AT ADDRESS
0 x 0000 – 0 x 1FFF
ACCESSIBLE WHEN
PMOVLAY = 0
PROGRAM MEMORY
15 14 13 12 11 10 9
15 14 13 12 11 10 9
NOTE: IDMA AND BDMA HAVE SEPARATE DMA CONTROL REGISTERS.
0
0
U
0
IDMA CONTROL (U = UNDEFINED AT RESET)
OVLAY
SHOULD ALWAYS BE WRITTEN WITH ZEROS.
DMA
RESERVED SET TO 0
U
RESERVED SET TO 0
0
RESERVED SET TO 0
U
0
U
0
U
0
IDMA OVERLAY
0 x 2000 –
0 x 3FFF
U
0
IDMAA ADDRESS
U
8
8
0
U
7
0
7
SHORT READ ONLY
0 = ENABLE
1 = DISABLE
IDDMOVLAY
IDMAD DESTINATION MEMORY TYPE
0 = PM
1 = DM
U
6
0
6
5
5
U
0
U
4
4
0
ACCESSIBLE WHEN
DMOVLAY = 0
ALWAYS
ACCESSIBLE
AT ADDRESS
0 x 2000 – 0 x 3FFF
DATA MEMORY
ADSP-2185M
3
0
3
U
IDPMOVLAY
U
2
2
OVLAY
0
DMA
1
1
U
0
0
0
U
0
DM (0x3FE7)
DM (0x3FE0)
0 x 0000 –
0 x 1FFF