ADUC7023BCP6Z62I Analog Devices Inc, ADUC7023BCP6Z62I Datasheet - Page 70

• Manufacturer Part Number: ADUC7023BCP6Z62I
• Description: Flash ARM7+8-ch,12-B ADC & 4x12-B DAC IC
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7023BCP6Z62I

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 44MHz
• Connectivity: I²C, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 62KB (62K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 12 x12b; D/A 4x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 40-LFCSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADuC7023
PULSE-WIDTH MODULATOR
PULSE-WIDTH MODULATOR GENERAL OVERVIEW
The ADuC7023 integrates a 5-channel pulse-width modulator
(PWM) interface. The PWM outputs can be configured to drive
an H-bridge or can be used as standard PWM outputs. On
power-up, the PWM outputs default to H-bridge mode. This
ensures that the motor is turned off by default. In standard
PWM mode, the outputs are arranged as three pairs of PWM
pins. Users have control over the period of each pair of outputs
and over the duty cycle of each individual output.
Table 83. PWM MMRs
MMR Name
PWMCON1
PWM0COM0
PWM0COM1
PWM0COM2
PWM0LEN
PWM1COM0
PWM1COM1
PWM1COM2
PWM1LEN
PWM2COM0
PWM2COM1
PWMCLRI
Description
PWM Control Register 1.
Compare Register 0 for PWM Output 0 and
PWM Output 1.
Compare Register 1 for PWM Output 0 and
PWM Output 1.
Compare Register 2 for PWM Output 0 and
PWM Output 1.
Frequency control for PWM Output 0 and PWM
Output 1.
Compare Register 0 for PWM Output 2 and
PWM Output 3.
Compare Register 1 for PWM Output 2 and
PWM Output 3.
Compare Register 2 for PWM Output 2 and
PWM Output 3.
Frequency control for PWM Output 2 and PWM
Output 3.
Compare Register 0 for PWM Output 4
Compare Register 1 for PWM Output 4
PWM interrupt clear.
Rev. B | Page 70 of 96
In all modes, the PWMxCOMx MMRs control the point at
which the PWM outputs change state. An example of the first
pair of PWM outputs (PWM0 and PWM1) is shown in Figure 40.
The PWM clock is selectable via PWMCON1 with one of the
following values: UCLK divided by 2, 4, 8, 16, 32, 64, 128, or
256. The length of a PWM period is defined by PWMxLEN.
The PWM waveforms are set by the count value of the 16-bit
timer and the compare registers contents, as shown with the
PWM0 and PWM1 waveforms in Figure 40.
The low-side waveform, PWM1, goes high when the timer
count reaches PWM0LEN, and it goes low when the timer
count reaches the value held in PWM0COM2 or when the
high-side waveform (PWM0) goes low.
The high-side waveform, PWM0, goes high when the timer
count reaches the value held in PWM0COM0, and it goes low
when the timer count reaches the value held in PWM0COM1.
PWMCON1 Control Register
Name:
Address:
Default value:
Access:
Function:
HIGH SIDE
LOW SIDE
(PWM0)
(PWM1)
PWM0COM2
PWM0COM1
PWM0COM0
PWM0LEN
PWMCON1
0xFFFF0F80
0x0012
Read and write
This is a 16-bit MMR that configures the
PWM outputs.
Figure 40. PWM Timing