ADUC7060BSTZ32-RL Analog Devices Inc, ADUC7060BSTZ32-RL Datasheet - Page 98
![DUAL 24-BIT AFE AND ARM 7 I.C](/photos/6/59/65923/505-48-lqfp_sml.jpg)
ADUC7060BSTZ32-RL
Manufacturer Part Number
ADUC7060BSTZ32-RL
Description
DUAL 24-BIT AFE AND ARM 7 I.C
Manufacturer
Analog Devices Inc
Series
MicroConverter® ADuC7xxxr
Datasheet
1.EVAL-ADUC7061MKZ.pdf
(108 pages)
Specifications of ADUC7060BSTZ32-RL
Design Resources
4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) Low power, Long Range, ISM Wireless Measuring Node (CN0164)
Core Processor
ARM7
Core Size
16/32-Bit
Speed
10MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
POR, PWM, Temp Sensor, WDT
Number Of I /o
14
Program Memory Size
32KB (16K x 16)
Program Memory Type
FLASH
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
2.375 V ~ 2.625 V
Data Converters
A/D 5x24b, 8x24b, D/A 1x14b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
48-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADUC7060BSTZ32-RL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
ADuC7060/ADuC7061
Table 107. SPICON MMR Bit Designations
Bit
15:14
13
12
11
10
9
8
7
6
5
4
3
2
Name
SPIMDE
SPITFLH
SPIRFLH
SPICONT
SPILP
SPIOEN
SPIROW
SPIZEN
SPITMDE
SPILF
SPIWOM
SPICPO
SPICPH
Description
SPI IRQ mode bits. These bits are configured when transmit/receive interrupts occur in a transfer.
[00] = transmit interrupt occurs when 1 byte has been transferred. Receive interrupt occurs when one or more bytes
have been received into the FIFO.
[01] = transmit interrupt occurs when 2 bytes have been transferred. Receive interrupt occurs when two or more
bytes have been received into the FIFO.
[10] = transmit interrupt occurs when 3 bytes have been transferred. Receive interrupt occurs when three or more
bytes have been received into the FIFO.
[11] = transmit interrupt occurs when 4 bytes have been transferred. Receive interrupt occurs when the receive FIFO
is full or 4 bytes are present.
SPI transmit FIFO flush enable bit.
Set this bit to flush the transmit FIFO. This bit does not clear itself and should be toggled if a single flush is required. If
this bit is left high, then either the last transmitted value or 0x00 is transmitted, depending on the SPIZEN bit. Any
writes to the transmit FIFO are ignored while this bit is set.
Clear this bit to disable transmit FIFO flushing.
SPI receive FIFO flush enable bit.
Set this bit to flush the receive FIFO. This bit does not clear itself and should be toggled if a single flush is required. If
this bit is set, all incoming data is ignored and no interrupts are generated. If set and SPITMDE = 0, a read of the
receive FIFO initiates a transfer.
Clear this bit to disable receive FIFO flushing.
Continuous transfer enable.
Set by user to enable continuous transfer. In master mode, the transfer continues until no valid data is available in the
transmit register. SS is asserted and remains asserted for the duration of each 8-bit serial transfer until the transmit
register is empty.
Cleared by user to disable continuous transfer. Each transfer consists of a single 8-bit serial transfer. If valid data exists
in the SPITX register, then a new transfer is initiated after a stall period of one serial clock cycle.
Loopback enable bit.
Set by user to connect MISO to MOSI and test software.
Cleared by user to be in normal mode.
Slave MISO output enable bit.
Set this bit for MISO to operate as normal.
Clear this bit to disable the output driver on the MISO pin. The MISO pin is open drain when this bit is cleared.
SPIRX overflow overwrite enable.
Set by user, the valid data in the receive register is overwritten by the new serial byte received.
Cleared by user, the new serial byte received is discarded.
SPI transmit zeros when transmit FIFO is empty.
SPI transfer and interrupt mode.
Set by user to initiate transfer with a write to the SPITX register. Interrupt occurs only when the transmit FIFO is empty.
Cleared by user to initiate transfer with a read of the SPI register. Interrupt occurs only when the receive FIFO is full.
LSB first transfer enable bit.
SPI wired or mode enable bit.
Set to 1 to enable the open-drain data output enable. External pull-ups are required on data out pins.
Clear for normal output levels.
Serial clock polarity mode bit.
Set by user, the serial clock idles high.
Serial clock phase mode bit.
Set this bit to transmit 0x00 when there is no valid data in the transmit FIFO.
Clear this bit to transmit the last transmitted value when there is no valid data in the transmit FIFO.
Set by user, the LSB is transmitted first.
Cleared by user, the MSB is transmitted first.
Cleared by user, the serial clock idles low.
Set by user, the serial clock pulses at the beginning of each serial bit transfer.
Cleared by user, the serial clock pulses at the end of each serial bit transfer.
Rev. B | Page 98 of 108