ADUM1301WTRWZ-RL Analog Devices Inc, ADUM1301WTRWZ-RL Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADUM1301WTRWZ-RL
Manufacturer Part Number
ADUM1301WTRWZ-RL
Description
3-5.5V DC 10Mbit/sc 3Chnl Dgtl 2Txr1Rxr
Manufacturer
Analog Devices Inc
Series
iCoupler®r
Datasheet
1.ADUM1300BRWZ.pdf
(28 pages)
Specifications of ADUM1301WTRWZ-RL
Inputs - Side 1/side 2
2/1
Number Of Channels
3
Isolation Rating
2500Vrms
Voltage - Supply
2.7 V ~ 5.5 V
Data Rate
10Mbps
Propagation Delay
32ns
Output Type
Logic
Package / Case
16-SOIC (0.300", 7.5mm Width)
Operating Temperature
-40°C ~ 125°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
ADuM1300/ADuM1301
Parameter
1
2
3
4
5
6
7
8
The supply current values are for all three channels combined when running at identical data rates. Output supply current values are specified with no output load present. The
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
t
t
recommended operating conditions.
Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of the isolation
barrier. Opposing-directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on opposing
sides of the isolation barrier.
CM
sustained while maintaining V
range over which the common mode is slewed.
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in signal data rate. See Fi
per-channel supply current for unloaded and loaded conditions. See the P
data rate.
from the 50% level of the rising edge of the V
supply current associated with an individual channel operating at a given data rate may be calculated as described in the P
Figure 8
supply currents as a function of data rate for ADuM1300/ADuM1301 channel configurations.
PHL
PSK
For All Models
is the magnitude of the worst-case difference in t
H
propagation delay is measured from the 50% level of the falling edge of the V
Output Disable Propagation Delay
Output Enable Propagation Delay (High
Output Rise/Fall Time (10% to 90%)
Common-Mode Transient Immunity at
Common-Mode Transient Immunity at
Refresh Rate
Input Dynamic Supply Current per Channel
Output Dynamic Supply Current per Channel
is the maximum common-mode voltage slew rate that can be sustained while maintaining V
Logic High Output
5 V/3 V Operation
3 V/5 V Operation
Logic Low Output
5 V/3 V Operation
3 V/5 V Operation
5 V/3 V Operation
3 V/5 V Operation
5 V/3 V Operation
3 V/5 V Operation
(High/Low to High Impedance)
Impedance to High/Low)
for information on per-channel supply current as a function of data rate for unloaded and loaded conditions. See
7
O
7
< 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient magnitude is the
Ix
signal to the 50% level of the rising edge of the V
PHL
8
or t
8
PLH
Symbol
t
t
t
|CM
|CM
f
I
I
that is measured between units at the same operating temperature, supply voltages, and output load within the
r
DDI (D)
DDO (D)
PHZ
PZH
R
/t
F
, t
, t
H
L
|
|
PLH
PZL
ower Consumption
Rev. H | Page 10 of 28
Min
25
25
Ix
signal to the 50% level of the falling edge of the V
Ox
section for guidance on calculating the per-channel supply current for a given
signal.
O
> 0.8 V
Typ
6
6
3.0
2.5
35
35
1.2
1.1
0.19
0.10
0.03
0.05
DD2
. CM
L
is the maximum common-mode voltage slew rate that can be
Figure 9
ower Consumption
Max Unit
8
8
gure 6
mA/Mbps
mA/Mbps
mA/Mbps
mA/Mbps
ns
ns
ns
ns
kV/μs
kV/μs
Mbps
Mbps
through
Ox
through
signal. t
Figure 12
Figure 8
PLH
Test Conditions
C
C
C
V
transient magnitude = 800 V
V
transient magnitude = 800 V
section. See
propagation delay is measured
L
L
L
Ix
Ix
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= V
= 0 V, V
for information on
DD1
for total V
or V
CM
Figure 6
= 1000 V,
DD2
DD1
, V
and V
CM
through
= 1000 V
DD2