CS4207-DNZ Cirrus Logic Inc, CS4207-DNZ Datasheet - Page 31
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CS4207-DNZ
Manufacturer Part Number
CS4207-DNZ
Description
IC Low Pwr,4/6 HD Aud Codec W/HP Amp
Manufacturer
Cirrus Logic Inc
Type
Audio Codecr
Datasheet
1.CS4207-DNZ.pdf
(144 pages)
Specifications of CS4207-DNZ
Resolution (bits)
24 b
Number Of Adcs / Dacs
2 / 3
Sigma Delta
Yes
Dynamic Range, Adcs / Dacs (db) Typ
105 / 110
Voltage - Supply, Analog
2.97 V ~ 5.25 V
Voltage - Supply, Digital
2.97 V ~ 5.25 V
Operating Temperature
-40°C ~ 105°C
Mounting Type
Surface Mount
Package / Case
48-QFN
Package
48WQFN
Number Of Channels Per Chip
16
Adc/dac Resolution
24 Bit
Gain Control
Programmable
Number Of Dacs
3
Number Of Dac Outputs
2
Operating Supply Voltage
1.8|3.3|5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
598-1798
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS4207-DNZ
Manufacturer:
CIRRUS
Quantity:
8
Company:
Part Number:
CS4207-DNZ
Manufacturer:
CIRRUS
Quantity:
2 011
DS880F1
5.1.2
If the codec has detected that the link is entering a Link Reset state (see description below), all Unsolicited
Response requests will be buffered. Once the link is in the Link Reset state, with RESET asserted low,
the codec will request a power state change and initialization request. Following the codec initialization
cycle where a unique address is provided to the CS4207, the codec will then wait for the first verb to be
received before issuing the Unsolicited Response to prevent the response from being lost due to software
transition to active power state.
The Link Reset entry sequence is defined as follows:
1. The HD Audio Bus controller synchronously completes the current frame but does not signal Frame
2. The HD Audio Bus controller synchronously asserts RESET four (or more) BITCLK cycles after the
3. BITCLK is stopped a minimum of four clocks, four rising edges, after the assertion of RESET.
In the event of a system bus (PCI Bus) reset, the above sequence does not complete, and RESET is asyn-
chronously asserted immediately and unconditionally.
When the codec returns to D0 from the D3 lower power state, the state of the presence detection bits will
be correct. If the codec power has been removed, the state of the presence detection bits will be reset to
the default value and the codec WILL NOT report this by setting the PS-SettingsReset bit for the affected
Pin Widget(s). (HDA015-B, March 1,2007 stays that the PS-SettingsReset bit will be set for the affected
Pin widget).
S/PDIF Receiver Presence Detect
The presence detect scheme for the S/PDIF Receiver will use the logic state transition of the “LOCK” or
“UNLOCK” indicator for the incoming digital stream. The “LOCK” and “UNLOCK” indicators are sticky bits
(edge-triggered) which indicate the current state of the receiver. These bits are located in the Vendor De-
fined Verb at F70, see
ceiver Input Converter Widget is “enabled” and the “LOCK” indicator is a “1”, then the Presence Detect bit
in the Pin Sense register will be set to ‘1’. The S/PDIF IN Converter Widget (NID=07h) and the S/PDIF
Receiver pin widget (NID=0Fh) must be in the D0 state to support presence detect using this method de-
scribed.
With an incoming valid S/PDIF signal applied to the SPDIF_IN pin, the “LOCK” status will be valid approx-
imately 200 S/PDIF frames following the receiver being enabled.
Sync (SYNC) during the last eight SDO bit times.
completion of the current frame.
“S/PDIF RX/TX Interface Status (CIR = 0000h)” on p
128. When the S/PDIF Re-
CS4207
31