CY7C65620-56LFXC Cypress Semiconductor Corp, CY7C65620-56LFXC Datasheet - Page 12
![IC,Bus Controller,LLCC,56PIN](/photos/6/83/68307/cy7c65620-56lfxc_sml.jpg)
CY7C65620-56LFXC
Manufacturer Part Number
CY7C65620-56LFXC
Description
IC,Bus Controller,LLCC,56PIN
Manufacturer
Cypress Semiconductor Corp
Series
EZ-USB HX2LP™r
Datasheet
1.CY7C65620-56LTXC.pdf
(25 pages)
Specifications of CY7C65620-56LFXC
Controller Type
USB 2.0 Hub Controller
Interface
USB/Serial
Voltage - Supply
3.15 V ~ 3.45 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
56-VQFN Exposed Pad, 56-HVQFN, 56-SQFN, 56-DHVQFN
Current - Supply
231mA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
CY4606 - KIT EZ-USB HX2LP 4PORT HUBCY4605 - KIT EZ-USB HX2LP 2PORT HUB
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
428-2260
CY7C65620-56LFXC
CY7C65620-56LFXC
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CY7C65620-56LFXC
Manufacturer:
CYPRESS
Quantity:
240
Part Number:
CY7C65620-56LFXC
Manufacturer:
CYPRESS/赛普拉斯
Quantity:
20 000
Part Number:
CY7C65620-56LFXCES
Manufacturer:
CYP
Quantity:
20 000
Company:
Part Number:
CY7C65620-56LFXCT
Manufacturer:
CYPRESS
Quantity:
1 000
Part Number:
CY7C65620-56LFXCT
Manufacturer:
CYPRESS/赛普拉斯
Quantity:
20 000
Configuration Options
Systems using CY7C656xx have the option of using a fuse
ROM, which is preset at the factory to configure the hub.
Otherwise, it must have an external EEPROM for the device to
have a unique VID, PID, and DID. The CY7C656xx can commu-
nicate with SPI EEPROM that are either double byte addressed
or single byte with the ninth bit within the instruction byte, such
as the 24LC040 parts use. The 25LC080 EEPROM uses the
double byte address format. Therefore, the CY7C656xx can
communicate with these parts. The '010s and '020s use the
same command format that is used to interface with the ‘040 and
hence these can also be used to interface with the CY7C656xx.
If the attached EEPROM is blank (0xFF) the hub enumerates as
a vendor class device. In this configuration, the hub connects to
the Cypress driver to allow programming of the EEPROM. When
the EEPROM is programmed, a power cycle configures the chip
as a hub class device.
0xD0 Load
With this EEPROM format, only a unique VID, PID, and DID must
be present in the external SPI EEPROM. The contents of the
EEPROM must contain this information in the following format:
0xD2 Load
Document Number: 38-08037 Rev. *L
Byte
10
12
11
0
1
2
3
4
5
6
7
8
9
0xD2
VID (LSB)
VID (MSB)
PID (LSB)
PID (MSB)
reserved
DID (MSB)
EnabledOverCurrentTimer[3:0],
DisableOvercurrentTimer[3:0]
ActivePorts[3:0], RemovablePorts[3:0]
MaxPower
HubControllerPower
PowerOnTimer
IllegalHubDescriptor, CompoundDevice,
FullspeedOnly, NoPortIndicators, Reserved,
GangPowered, Reserved, Reserved
Byte
0
1
2
3
4
5
6
Value (MSB->LSB)
DID (MSB)
VID (MSB)
PID (MSB)
VID (LSB)
PID (LSB)
reserved
Value
0xD0
Byte 0: 0xD2
Byte 1: VID (LSB)
Byte 2: VID (MSB)
Byte 3: PID (LSB)
Byte 4: PID (MSB)]
Byte 5: Reserved
Byte 6: DID (MSB)]
Byte 7: EnabledOvercurrentTimer[3:0],
DisabledOvercurrentTimer[3:0]
Byte 8: ActivePorts[3:0], RemovablePorts[3:0]
Byte 9: MaximumPower
Byte 10: HubControllerPower
Byte 11: PowerOnTimer
Needs to be programmed with 0xD2
Least Significant Byte of Vendor ID
Most Significant Byte of Vendor ID
Least Significant Byte of Product ID
Most Significant Byte of Product ID
Reserved
Most Significant Byte of Device ID
Count time in ms for filtering overcurrent detection. Bits 7–4
are for an enabled port, and bits 3–0 are for a disabled port.
Both range from 0 ms to 15 ms. See section
on page 4. Default: 8 ms = 0x88.
Bits 7–4 are the ActivePorts[3:0] bits that indicates if the cor-
responding port is usable. For example, a two-port hub that
uses ports 1 and 4 would set this field to 0x09. The total num-
ber of ports reported in the Hub Descriptor: bNbrPorts field is
calculated from this. Bits 3–0 are the RemovablePorts[3:0]
bits that indicates whether the corresponding logical port is
removable (set to high). Logical port numbers are from 1 to n
where n is the total number of active ports. If port 2 is disabled
then physical ports 1, 3, and 4 map to logical ports 1, 2, and
3. These bit values are reported appropriately in the
HubDescriptor:DeviceRemovable field. Default: 0xFF.
This value is reported in the ConfigurationDescriptor:bMax-
Power field and is the current in 2 mA increments that is re-
quired from the upstream hub. Default: 0x28 = 80 mA for full
speed and 0x57 = 174 mA for high speed.
This value is reported in the HubDescriptor:bHubContrCur-
rent field and is the current in milliamperes required by the
hub controller. Default: 0x50 = 80 mA for full speed and 0xAE
= 174 mA for high speed.
This
bPwrOn2PwrGood field and is the time in 2 ms intervals from
the SetPortPower command until the power on the corre-
sponding downstream port is good. Default: 0x32 = 100 ms.
value
is
reported
in
the
CY7C656xx
HubDescriptor:
Port Indicators
Page 12 of 25
[+] Feedback