DSPIC33FJ128MC706T-I/PT Microchip Technology, DSPIC33FJ128MC706T-I/PT Datasheet - Page 165

• Manufacturer Part Number: DSPIC33FJ128MC706T-I/PT
• Description: IC,DSP,16-BIT,CMOS,TQFP,64PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ128MC706T-I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 16x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA330013 - MODULE PLUG-IN DSPIC33 100TQFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.0
The Timer1 module is a 16-bit timer, which can serve
as the time counter for the real-time clock or operate as
a free-running interval timer/counter. Timer1 can oper-
ate in three modes:
• 16-bit Timer
• 16-bit Synchronous Counter
• 16-bit Asynchronous Counter
FIGURE 12-1:
© 2009 Microchip Technology Inc.
Note:
TIMER1
This data sheet summarizes the features
of the dsPIC33FJXXXMCX06/X08/X10
family of devices. However, it is not
intended to be a comprehensive reference
source. To complement the information in
this data sheet, refer to Section 11.
“Timers” (DS70205) in the “dsPIC33F
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
SOSCO/
SOSCI
Set T1IF
T1CK
16-BIT TIMER1 MODULE BLOCK DIAGRAM
TGATE
0
1
Reset
Equal
dsPIC33FJXXXMCX06/X08/X10
SOSCEN
Comparator
TMR1
PR1
Q
Q
Gate
Sync
CK
T
CY
D
Timer1 also supports the following features:
• Timer gate operation
• Selectable prescaler settings
• Timer operation during CPU Idle and Sleep
• Interrupt on 16-bit Period register match or falling
Figure 12-1 presents a block diagram of the 16-bit
timer module.
To configure Timer1 for operation, do the following:
1.
2.
3.
4.
5.
6.
modes
edge of external gate signal
Set the TON bit (= 1) in the T1CON register.
Select the timer prescaler ratio using the
TCKPS<1:0> bits in the T1CON register.
Set the Clock and Gating modes using the TCS
and TGATE bits in the T1CON register.
Set or clear the TSYNC bit in T1CON to select
synchronous or asynchronous operation.
Load the timer period value into the PR1
register.
If interrupts are required, set the interrupt enable
bit, T1IE. Use the priority bits, T1IP<2:0>, to set
the interrupt priority.
TSYNC
1x
01
00
0
1
TON
TGATE
TCS
Sync
TCKPS<1:0>
1, 8, 64, 256
Prescaler
2
DS70287C-page 163