DSPIC33FJ16MC101-I/SO Microchip Technology, DSPIC33FJ16MC101-I/SO Datasheet - Page 258

• Manufacturer Part Number: DSPIC33FJ16MC101-I/SO
• Description: 16-bit Motor Control DSC Family, 16 MIPS, 16KB Flash, 1KB RAM 20 SOIC .300in TUB
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ16MC101-I/SO

• Processor Series: dsPIC33F
• Core: dsPIC
• Data Bus Width: 16 bit
• Program Memory Type: Flash
• Program Memory Size: 16 KB
• Interface Type: SPI, I2C, UART, JTAG
• Number Of Programmable I/os: 35
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Development Tools By Supplier: MPLAB IDE Software
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• Featured Product: PIC24FJ/33FJ MCUs & dsPIC® DSCs
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 16 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 15
• Eeprom Size: -
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (0.295", 7.50mm Width)
• Lead Free Status / Rohs Status: Details

dsPIC33FJ16GP101/102 AND dsPIC33FJ16MC101/102
FIGURE 26-2:
TABLE 26-16: EXTERNAL CLOCK TIMING REQUIREMENTS
DS70652C-page 258
AC CHARACTERISTICS
OS10
OS20
OS25
OS30
OS31
OS40
OS41
OS42
Note 1:
Param
No.
OSC1
CLKO
2:
3:
4:
5:
6:
F
T
T
TosL,
TosH
TosR,
TosF
TckR
TckF
G
Symb
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
Instruction cycle period (T
are based on characterization data for that particular oscillator type under standard operating conditions
with the device executing code. Exceeding these specified limits may result in an unstable oscillator
operation and/or higher than expected current consumption. All devices are tested to operate at “min.”
values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the
“max.” cycle time limit is “DC” (no clock) for all devices.
Measurements are taken in EC mode. The CLKO signal is measured on the OSC2 pin.
These parameters are characterized by similarity, but are tested in manufacturing at F
These parameters are characterized by similarity, but are not tested in manufacturing.
Data for this parameter is Preliminary. This parameter is characterized, but not tested in manufacturing.
OSC
CY
IN
M
External CLKI Frequency
(External clocks allowed only
in EC and ECPLL modes)
Oscillator Crystal Frequency
T
Instruction Cycle Time
External Clock in (OSC1)
High or Low Time
External Clock in (OSC1)
Rise or Fall Time
CLKO Rise Time
CLKO Fall Time
External Oscillator
Transconductance
OSC
EXTERNAL CLOCK TIMING
= 1/F
OS41
Characteristic
OSC
(3,5)
Q1
(3,5)
CY
(4)
OS20
) equals two times the input oscillator time-base period. All specified values
(2,4)
Q2
(5)
(5)
Preliminary
OS25
Q3
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature
0.45 x T
OS40
31.25
62.5
Min
DC
3.0
Q4
10
31
14
—
—
—
OSC
OS30
Q1
Typ
—
—
—
—
—
—
—
—
16
6
6
OS30
(1)
Q2
-40°C ≤ T
-40°C ≤T
Q3
Max
DC
DC
32
10
32
33
20
10
10
18
—
OS31
A
A
© 2011 Microchip Technology Inc.
Q4
≤ +85°C for Industrial
≤+125°C for Extended
OS31
Units
mA/V V
MHz
MHz
MHz
kHz
ns
ns
ns
ns
ns
ns
IN
= 32 MHz only.
EC
MS
HS
SOSC
EC
EC
T
A
DD
Conditions
= +25ºC
= 3.3V
—
—
—
—