A6265KLPTR-T Allegro Microsystems Inc, A6265KLPTR-T Datasheet
A6265KLPTR-T
Specifications of A6265KLPTR-T
Related parts for A6265KLPTR-T
A6265KLPTR-T Summary of contents
Page 1
Features and Benefits ▪ Constant current LED drive ▪ 6 supply ▪ Boost or buck-boost modes ▪ Drives between 2 and 10 LEDs in series ▪ Programmable switching frequency 100 to 700 kHz ▪ Open LED overvoltage ...
Page 2
... A6265 Selection Guide Part Number A6265KLP-T 96 pieces per tube A6265KLPTR-T 4000 pieces per 13-in. reel Absolute Maximum Ratings With respect to GND at T Characteristic Load Supply Voltage Pins FF1, EN Pins FF2, CKOUT Pin OSC Pin SG Pins LA, LN Pins LF Pins LP Pin SP, SN Pin VREG ...
Page 3
A6265 Terminal List Table Number – Automotive High Current LED Controller Pin-out Diagram FF1 FF2 3 ...
Page 4
A6265 VBAT Buck-Boost VREG FF2 FF1 EN VBAT Boost VREG FF2 FF1 EN See Functional Description section Automotive High Current LED Controller Functional Block Diagrams R SL VIN LED Open and V REG ...
Page 5
A6265 ELECTRICAL CHARACTERISTICS Characteristics Supply and Reference 2 V Functional Operating Range IN V Quiescent Current IN VREG Output Voltage Gate Output Drive Turn-On Time Turn-Off Time Maximum Duty Cycle Pull-Up On Resistance Pull-Down On Resistance Output High Voltage Output ...
Page 6
A6265 ELECTRICAL CHARACTERISTICS Characteristics Oscillator (continued) OSC Watchdog Period CKOUT Output High Voltage CKOUT Output Low Voltage LED Current Sense Input Bias Current LN (BB mode) 3 Input Bias Current LP (BB mode Input Bias Current LN (B ...
Page 7
A6265 The A6265 is a DC-DC converter controller that is designed to drive series-connected high power LEDs in automotive applica- tions. It provides programmable constant current output at load voltages and currents limited only be the external components. For automotive ...
Page 8
A6265 LF Single diode forward voltage reference input. Measures the forward voltage of the first LED. This value is used as a reference against the voltage on the LA pin to detect possible shorted LEDs in the LED string. Circuit ...
Page 9
A6265 LED Current Level The LED current is determined by a combination of the LED sense resistor, R threshold voltage and the voltage between the IREF pin IDL and GND ( V ). IREF The 100% current level, ...
Page 10
A6265 Diagnostics The circuit includes several diagnostic and safety functions to assist in ensuring safe operation of the LEDs, the A6265, and the external components. When any fault is detected, one or both of the fault flag outputs, FF1 and ...
Page 11
A6265 These measurements are used to determine if there is an open circuit, if one or more LEDs are shorted, if the output is shorted there is a short across the LED string. Each condition is described in ...
Page 12
A6265 gate-source junction can be used. The FF1 provides a sink current 1.3 mA. This circuit can be used to avoid most hazardous conditions and protect the circuit components from over-stress. Note that under extreme cases, the ...
Page 13
A6265 Component Selection External component selection is critical to the successful appli- cation of the LED driver. Although the inductor, the switching MOSFET, and the output capacitor are the most critical elements, the specification of the rectifying diode and sense ...
Page 14
A6265 • buck-boost configuration: ▫ The maximum average inductor current is approximately: (max (max) × (V (min L(av) LED IN ▫ The inductor current ripple is approximately × ...
Page 15
A6265 total gate charge will determine the average current required from the internal regulator and thus the power dissipation. Output Capacitor There are several points to consider when selecting the output capacitor. Unlike some switch-mode regulators, the value of the ...
Page 16
A6265 Package LP 16-Pin TSSOP with Exposed Thermal Pad 5.00±0. NOM 16X 0.10 C 0.30 0.19 0.65 BSC Automotive High Current LED Controller 8º 0º 0.20 0.09 3 NOM 4.40±0.10 6.40±0.20 0.60 ±0.15 1.00 ...
Page 17
A6265 Copyright ©2011, Allegro MicroSystems, Inc. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such de par tures from the detail spec tions as may be required to per- mit improvements in the ...