V680-HAM42-DRT Omron, V680-HAM42-DRT Datasheet - Page 9

• Manufacturer Part Number: V680-HAM42-DRT
• Description: V680 DeviceNet RFID Ctrl
• Manufacturer: Omron

Specifications of V680-HAM42-DRT

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Part Names and Operating Modes
V680-HAM42-DRT
Part Names
Operating Modes
Note 1. The V600-compatible Trigger and Auto Modes can be used with the same I/O settings and control methods that are used with the V600-
Commands (4-byte, 26-byte, 58-byte Access Mode)
0
1
2
3
4
5
6
7
8
9
Reading
Writing
Mode Symbol
2. Communications with the host device will be offline while the Communications Test Mode or Noise Measurement Mode is being used.
Operation indicators
HAM42-DRT.
4CH
16CH
32CH
SYNC1
SYNC2
AUTO1
AUTO2
TEST
NOISE
---
MS: ID Slave status
NS: Network status
TR: ID Tag communications status
NORMAL/ERROR: Result of communications with ID Tag
READ
WRITE
BIT SET
BIT CLEAR Previously specified bits (i.e., bits that are turned ON) are turned OFF in the ID Tag address specified for BIT CLEAR.
DATA FILL The specified continuous memory addresses in the ID Tag are filled with the same data.
DeviceNet Connector
Node Address Switches
Connects to DeviceNet Master Unit.
Enclosed connector model:
FKC2.5/5-ST-5.08-RFAUM (Phoenix Contact)
Node address switches (setting range: 00 to 63)
4-byte Access Mode
26-byte Access Mode
58-byte Access Mode
V600-compatible Trigger Mode, 100-ms output time
V600-compatible Trigger Mode, 500-ms output time
V600-compatible Auto Mode, 100-ms output time
V600-compatible Auto Mode, 500-ms output time
ID Tag Communications Test Mode (Checks standalone op-
eration of ID Slave.)
Noise Measurement Mode (Measures the noise around the
Antenna.)
Setting prohibited
Data in the ID Tag memory is read by specifying the memory address and the number of bytes to process.
(The number of bytes can be specified using the Access Mode.)
Data is written to the ID Tag by specifying the memory address, number of bytes to process, and the data.
(The number of bytes can be specified using the Access Mode.)
Previously specified bits (i.e., bits that are turned ON) are turned ON in the ID Tag address specified for BIT SET.
Description
OMRON
SOURCE : 24VDC 0.2A
OMRON Corporation
V680-HAM42-DRT, V680-HAM91/-HAM81
MS
NS
NODE No .
V680-HAM42-DRT
X10
1
NORMAL/ERROR
X10
T/R
FSM
0
MADE IN JAPAN
OFF
MODE
NOISE
TEST
AUTO2
3
7
RFID
6
2
AUTO1
bytes accessible in ID Tag
Read: 4 bytes
Write: 4 bytes
Read: 26 bytes
Write: 26 bytes
Read: 58 bytes
Write: 58 bytes
Read: 3 bytes
Write: 2 bytes
---
4CH
5
1
16CH
Maximum number of
SYNC2
32CH
SYNC1
4
0
Power Supply Terminals
Antenna Connector
Data/Error Code Indicators (Two-color LED)
Mode Switch
Connect to 24-VDC power.
Recommended Power Supply: S8VS-03024
(Manufactured by OMRON)
Enclosed connector model:
FKC2.5/3-ST-5.08-RF (Phoenix Contact)
Connects to a V680-series Antenna (V680-HS@)
Data (green)
Sets the operating mode of the ID Slave.
(Refer to the following table.)
Error code (red)
IN: 4 words
OUT: 4 words
(PLC inputs: 64 points,
PLC outputs: 64 points)
IN: 16 words
OUT: 16 words
(PLC inputs: 256 points,
PLC outputs: 256 points)
IN: 32 words
OUT: 32 words
(PLC inputs: 512 points,
PLC outputs: 512 points)
IN: 2 words
OUT: 2 words
---
Words allocated in Master Unit
9