NT631C-ST153-EV3 Omron, NT631C-ST153-EV3 Datasheet - Page 37

• Manufacturer Part Number: NT631C-ST153-EV3
• Description: 10.48-ColrDisplay,TFT,Ivy,Eng
• Manufacturer: Omron

Specifications of NT631C-ST153-EV3

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Communications with the Host
Features of the NT Link
20
The NT631/NT631C also supports OMRON’s high-speed 1:N NT Link that
provides faster 1:N communications. The only PLCs that support the high-
speed 1:N NT Link are CS1G/CS1H PLCs of version -EV1 and higher, CS1D
PLCs, and CJ1G/CJ1H/CJ1M PLCs.
In the following sections, the term NT Link is used to refer to the NT Link com-
munications method in general, the term 1:1 NT Link is used to refer specifi-
cally to NT Links with a 1:1 connection, and the term 1:N NT Link is used to
refer to both standard and high speed NT Links with 1:N connections. When
necessary, the standard 1:N NT Link is distinguished from the high-speed 1:N
NT Link.
The NT link has the following features.
• High-speed communications with specific types of PLCs can be executed.
• Writing in units of bits to the PLC memory area is possible.
• The NT link can be used even when the PLC is in the RUN mode. (When
• In the case of PTs that support the standard 1:N NT Link (NT20S, NT31,
• When using a C200HX/HG/HE(-Z)E PLC and standard 1:N NT Links, up
• When using a CQM1H PLC and standard 1:N NT Links, multiple 1:N NT
• Multiple 1:N NT Link systems (standard or high-speed) can be connected
• If the PLC supports the Programming Console function, the NT631/
• If the PLC supports the Device Monitor function, the NT631/NT631C can
The NT631/NT631C also supports OMRON’s high-speed 1:N NT Link.
This enables the other bits of words to which a touch switch has been al-
located to be allocated for other purposes (e.g. a lamp).
However, since data is written to the DM area in word units, the other bits
of words allocated to touch switches in this area cannot be used for other
purposes.
the host link method is used, the NT631/NT631C switches to the monitor
mode when the PLC is in the RUN mode.)
NT31C, NT600S, NT620S, NT620C, NT625C, NT631, NT631C) up to 8
PTs can be connected to one port of the PLC and used at the same time.
Up to 8 PTs (NT31, NT31C, NT631, and NT631C) can also be connected
simultaneously when the high-speed 1:N NT Link is being used.
All of the PTs connected to a PLC port must use either the standard or
high-speed 1:N NT Link; the two communications systems cannot share a
single port.
to three 1:N NT Link systems (i.e., 24 PTs) can be connected by installing
a Communications Board in the option slot of the CPU Unit. (Only the
standard 1:N NT Link can be used.) For details on the Communications
Board, refer to the SYSMAC Communications Board Operation Manual
(W304-E1-@).
Link systems can be connected by installing Serial Communications
Boards in the Inner Board slots. For details on the Serial Communications
Board, refer to the CQM1H Serial Communications Board Operation Man-
ual (W365-E1-@).
by installing a Communications Board in the Inner Board slot of the CPU
Unit for a CS1G/H/D PLC or installing a Serial Communications Unit on
the Backplane for a CS1G/H/D or a CJ1G/M/H PLC. For details on the
Communications Board/Communications Unit, refer to the CS/CJ-series
Serial Communications Board/Unit Operation Manual (W336-E1-@).
NT631C can be used as a Programming Console.
be used to change the PLC’s operating mode and read/change data in the
PLC’s memory areas.
Section 1-4