NT631C-ST153-EV3 Omron, NT631C-ST153-EV3 Datasheet - Page 59
NT631C-ST153-EV3
Manufacturer Part Number
NT631C-ST153-EV3
Description
10.48-ColrDisplay,TFT,Ivy,Eng
Manufacturer
Omron
Datasheet
1.NT-AL001.pdf
(315 pages)
Specifications of NT631C-ST153-EV3
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 59 of 315
- Download datasheet (4Mb)
Using a Memory Unit
Writing Screen Data to the
PT Using Automatic
Transmission (Memory
Unit to PT)
42
Reference:
1,2,3...
1. Check that the power supply to the NT631/NT631C is OFF, then set the
2. Switch the NT631/NT631C power ON.
3. Switch the NT631/NT631C power OFF, remove the Memory Unit.
In this mode, the system program or screen data in the Memory Unit is forcibly
written to NT631/NT631C irrespective of the setting status of the NT631/
NT631C.
Since data transmission by this method is faster than when the Support Tool
or system installer is used, it can save a lot of time. When transmitting the
same system program or screen data to multiple NT631/NT631C, this mode
becomes convenient.
SW1-4 ON: System program
• Setting SW2-4 to ON (System/Screen transmitted simultaneously) dis-
• Setting SW2-4 to ON (System/Screen transmitted simultaneously) dis-
DIP switches of the Memory Unit as follows after installing Memory Unit to
NT631/NT631C.
It is not strictly necessary to set SW2-1 to OFF (to disable writing to the
PT), but it is recommended to do so to avoid loss of data in the event of
operating errors.
ables the setting of SW1-4.
ables the setting of SW2-3, writes the system program into bank 0, and
the screen data into bank 1 at all times.
The screen data is automatically written into the Memory Unit. The screen
data in the NT631/NT631C is preserved.
The messages Preparing, Transmitting, Verifying, and Finished are dis-
played on the screen in accordance with the progress of data writing.
At the same time, the progress of the data writing status is displayed by the
means of the number of bytes and blocks (1 bank = 16 block = 1024k byte).
RUN LED operates as follows according to the processing status.
Preparing:
Transmitting:
Verifying:
Finished:
To operate NT631/NT631C continuously, switch the NT631/NT631C pow-
er back ON.
SW1
OFF: Screen data
SW2
SW2-3 ON: Bank 1
flashes at intervals of 1 second
flashes at intervals of 0.5 second
flashes at intervals of 0.5 second
lights up
OFF: Bank 0
SW2-4 ON: System/Screen transmitted simultaneously
OFF: System/Screen not transmitted simultaneously
Section 3-5
Related parts for NT631C-ST153-EV3
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NT631-ST151 BACKLIGHT
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
NT631-ST141 BACKLIGHT
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
3M 9-9PIN CBL, NT TO AB PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
3M 9-9PIN CBL, NT TO GE PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
50CM 9-9PIN CBL, NT TO AB PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
50CM 9-9PIN CBL, NT TO GE PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
5M 9-9PIN CBL, NT TO AB PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
5M 9-9PIN CBL, NT TO GE PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
10.48-ColrDisplay,TFT,Blk,Eng
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: