Si5338K-A-GM Silicon Laboratories Inc, Si5338K-A-GM Datasheet - Page 20

• Manufacturer Part Number: Si5338K-A-GM
• Description: Clock Generators & Support Products I2C-PRGRMBL clock generatr 0.16-700MHz
• Manufacturer: Silicon Laboratories Inc

Specifications of Si5338K-A-GM

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Si5338
3.5.1. Ordering a Custom NVM Configuration
The Si5338 is orderable with a factory-programmed
custom NVM configuration. This is the simplest way of
using the Si5338 since it generates the desired output
frequencies at power-up or after a power-on reset
(POR). This default configuration can be reconfigured in
RAM through the I
“3.5.2. Creating a New Configuration for RAM”).
Custom 7-bit I
Note that for the A/B/C devices, the I
is the logical “or” of the I
and the state of the I2C_LSB pin. If I2C_LSB pin
functionality is required, custom I
only be even numbers. For all other variants of the
device, custom I
numbers. See “AN411: Configuring the Si5338” for
more details.
The first step in ordering a custom device is generating
an NVM file which defines the input and output clock
frequencies and signal formats. This is easily done
using the ClockBuilder Desktop software (see "3.1.1.
ClockBuilder™ Desktop Software" on page 16). This
GUI based software generates an NVM file, which is
used by the factory to manufacture custom parts. Each
custom part is marked with a unique part number
identifying the specific configuration (e.g., Si5338C-
A00100-GM). Consult your local sales representative
for more details on ordering a custom Si5338.
3.5.2. Creating a New Configuration for RAM
Any Si5338 device can be configured by writing to
registers in RAM through the I
factory programmed device must be configured in this
manner.
The first step is to determine all the register values for
the required configuration. This can be accomplished by
one of two methods.
1. Create a device configuration (register map) using
20
ClockBuilder Desktop (v3.0 or later; see "3.1.1.
ClockBuilder™ Desktop Software" on page 16).
a. Configure the frequency plan.
b. Configure the output driver format and supply
c. Configure frequency and/or phase inc/dec (if
d. Configure spread spectrum (if desired).
e. Configure for zero-delay mode (if desired,
f.
g. Save the configuration using the Options >
voltage.
desired).
see "3.10.6. Zero-Delay Mode" on page 26).
If needed go to the Advanced tab and make
additional configurations.
2
C addresses may also be requested.
2
C addresses may be even or odd
2
C interface after power-up (see
2
C address LS bit in Register 27
2
C interface. A non-
2
C addresses may
2
C LS bit address
Rev. 1.0
2. Create a device configuration, register by register,
3.5.3. Writing a Custom Configuration to RAM
Writing a new configuration (register map) to the RAM
consists of pausing the LOL state-machine, writing new
values to the IC accounting for the write-allowed mask
(see AN411, “14. Si5338 Registers”), validating the
input clock or crystal, locking the PLL to the input with
the new configuration, restarting the LOL state-
machine, and calibrating the VCO for robust operation
across temperature. The flow chart in Figure 9
enumerates the details:
Note: The write-allowed mask specifies which bits must be
using AN411.
read and modified before writing the entire register
byte (a.k.a. read-modify-write). “AN428: Jump Start: In-
System, Flash-Based Programming for Silicon Labs’
Timing Products” illustrates the procedure defined in
Section 3.5.2 with ANSI C code.
Save Register Map File or Options > Save C
code Header.