XC2S400E-6FG456I Xilinx Inc, XC2S400E-6FG456I Datasheet - Page 28
![no-image](/images/no-image-200.jpg)
XC2S400E-6FG456I
Manufacturer Part Number
XC2S400E-6FG456I
Description
FPGA Spartan®-IIE Family 400K Gates 10800 Cells 357MHz 0.15um Technology 1.8V 456-Pin FBGA
Manufacturer
Xilinx Inc
Datasheet
1.XC2S50E-6TQG144C.pdf
(108 pages)
Specifications of XC2S400E-6FG456I
Package
456FBGA
Family Name
Spartan®-IIE
Device Logic Cells
10800
Device Logic Units
2400
Device System Gates
400000
Maximum Internal Frequency
357 MHz
Typical Operating Supply Voltage
1.8 V
Maximum Number Of User I/os
329
Ram Bits
163840
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Spartan-IIE FPGA Family: Functional Description
If CCLK is slower than F
BUSY. In this case, the above handshake is unnecessary,
and data can simply be entered into the FPGA every CCLK
cycle.
A configuration packet does not have to be written in one
continuous stretch, rather it can be split into many write
sequences. Each sequence would involve assertion of CS.
In applications where multiple clock cycles may be required
to access the configuration data before each byte can be
loaded into the Slave Parallel interface, a new byte of data
may not be ready for each consecutive CCLK edge. In such
a case the CS signal may be deasserted until the next byte
is valid on D0-D7. While CS is High, the Slave Parallel inter-
face does not expect any data and ignores all CCLK transi-
28
Figure 21: Loading Configuration Data for the Slave
CCLK Rising Edge
WRITE and CS
WRITE and CS
To CRC Check
Byte on Next
Configuration
Driving BUSY
Configuration
User Drives
User Drives
Goes High
Load One
After INIT
Data File?
Parallel Mode
End of
FPGA
High?
High
Low
CCNH
No
Yes
, the FPGA will never assert
Yes
No
DS001_19_032300
www.xilinx.com
tions. However, to avoid aborting configuration, WRITE
must continue to be asserted while CS is asserted during
CCLK transitions.
Abort
To abort configuration during a write sequence, deassert
WRITE while holding CS Low. The abort operation is initi-
ated at the rising edge of CCLK. The device will remain
BUSY until the aborted operation is complete. After aborting
configuration, data is assumed to be unaligned to word
boundaries and the FPGA requires a new synchronization
word prior to accepting any new packets.
Boundary-Scan Configuration Mode
In the boundary-scan mode, no nondedicated pins are
required, configuration being done entirely through the
IEEE 1149.1 Test Access Port (TAP).
Configuration through the TAP uses the special CFG_IN
instruction. This instruction allows data input on TDI to be
converted into data packets for the internal configuration
bus.
The following steps are required to configure the FPGA
through the boundary-scan port.
1. Load the CFG_IN instruction into the boundary-scan
2. Enter the Shift-DR (SDR) state
3. Shift a standard configuration bitstream into TDI
4. Return to Run-Test-Idle (RTI)
5. Load the JSTART instruction into IR
6. Enter the SDR state
7. Clock TCK (if selected) through the startup sequence
8. Return to RTI
Configuration and readback via the TAP is always available.
The boundary-scan mode simply locks out the other modes.
The boundary-scan mode is selected by a <10x> on the
mode pins (M0, M1, M2). Note that the PROGRAM pin must
be pulled High prior to reconfiguration. A Low on the PRO-
GRAM pin resets the TAP controller and no boundary scan
operations can be performed. See Xilinx Application Note
XAPP188
ration.
Readback
The configuration data stored in the Spartan-IIE FPGA con-
figuration memory can be read back for verification. Along
with the configuration data it is possible to read back the
contents of all flip-flops/latches, LUT RAMs, and block
RAMs. This capability is used for real-time debugging.
For more detailed information see Xilinx Application Note
XAPP176, Configuration and Readback of the Spartan-II
and Spartan-IIE FPGA Families.
instruction register (IR)
(the length is programmable)
for more information on boundary-scan configu-
DS077-2 (v2.3) June 18, 2008
Product Specification
R