9-1393792-3 TE Connectivity, 9-1393792-3 Datasheet - Page 405

• Manufacturer Part Number: 9-1393792-3
• Description: Electromechanical Relay DPDT 3A 5VDC 125Ohm Through Hole
• Manufacturer: TE Connectivity
• Type: Signal Relayr

Specifications of 9-1393792-3

• Contact Arrangement: DPDT
• Dc Coil Voltage: 5 V
• Coil Current: 40 mA
• Mounting: Through Hole

Dimensions are shown for
reference purposes only.
AGASTAT Time Delay Relay Timing Modes
On-Delay: Time delay is initiated upon application of a control signal (i.e.,
operating voltage or on 11-pin model closure of the control switch). The output
contacts energize at the end of the delay. Output contacts and the time delay
circuit reset upon removal of the control signal regardless of state.
Off-Delay: The output contacts energize when the control switch is closed.
The time delay is initiated upon opening of the control switch (operating
voltage is applied continuously). De-energization occurs at the end of the
delay. Output contacts energize and the time delay circuit resets upon closure
of the control switch.
Interval: Time delay is initiated upon application of a control signal (i.e.,
operating voltage or closure of the control switch on 11-pin models). The
output contacts energize when the control signal is applied. At the end of the
delay, the output contacts de-energize. Output contacts and the time delay
circuit reset upon removal of the control signal regardless of state.
On / Interval : Time delay 1 is initiated upon application of a control signal (i.e.,
operating voltage or closure of the control switch on 11-pin models). The
output contacts energize at the end of time delay 1 and de-energize at the end
of time delay 2. Output contacts and the time delay circuit reset upon removal
of the control signal regardless of state. Note: For the 48K series, delay 2 is
fixed at 0.5 seconds.
Note: When an external control switch is used, it must
be closed before the unit is energized. If external
control switch is open, the unit will not time out.
OPERATING VOLTAGE/
CONTROL SWITCH
OUTPUT
CONTACTS
OPERATING VOLTAGE/
CONTROL SWITCH
OUTPUT
CONTACTS
OPERATING VOLTAGE/
CONTROL SWITCH
OUTPUT
CONTACTS
OPERATING
VOLTAGE
CONTROL
SWITCH
OUTPUT
CONTACTS
ON / CLOSED
ON / CLOSED
ENERGIZED
ENERGIZED
ON / CLOSED
ENERGIZED
OFF / OPEN
OFF / OPEN
ENERGIZED
OFF / OPEN
DE-ENER.
DE-ENER.
DE-ENER.
CLOSED
DE-ENER.
OPEN
OFF
ON
DELAY 1
DELAY
DELAY
Dimensions are in inches over
(millimeters) unless otherwise
specified.
DELAY
DELAY 2
Catalog 1308242
Issued 3-03
On-Delay / Off-Delay: Time delay is initiated for delay 1 upon closure of the
control switch, for delay 2 upon opening of the control switch. (Operating
voltage is applied continuously.) Output contacts energize at the end of time
delay 1, and de-energize at the end of time delay 2. If the control state is
reversed during the time delay, the time delay circuit automatically resets to
zero. Note: For the 48K series, time delays 1 and 2 are identical.
Repeat Cycle: Application of the operating voltage starts time delay 1. Upon
expiration of this delay, the output contacts energize. Time delay 2 begins
simultaneously. At the end of time delay 2, the output contacts de-energize,
and a new cycle begins. The cycles continue until power is removed. To reset
the timer, input voltage must be removed. The state of the output contacts
may be reversed on the 11-pin 48K by closing the control switch. Note: For the
48K series, the time delays are identical.
Accumulating On-Delay: Time delay is initiated upon closure of the control
switch. (Operating voltage is applied continuously.) Energization of the output
contacts occurs at the end of the delay. If the control switch is opened during
the time delay, the time delay pauses, and the relay holds (remembers) the
delay accumulated so far. The time delay resumes when the control switch
is re-closed. After energization, reset by opening the control switch. Regard-
less of state, reset by removing the operating voltage.
One Shot (Latching Interval): Operating voltage must be applied continu-
ously. Output contacts energize and time delay is initiated upon closure of the
control switch. Once closed, state of control switch has no further influence
until time delay has expired. Upon expiration of time delay, output contacts de-
energize and timer is reset by opening the control switch.
Specifications and availability
subject to change.
OPERATING
VOLTAGE
OUTPUT
CONTACTS
OPERATING
VOLTAGE
CONTROL
SWITCH
OUTPUT
CONTACTS
OPERATING
VOLTAGE
CONTROL
SWITCH
OUTPUT
CONTACTS
OPERATING
VOLTAGE
CONTROL
SWITCH
OUTPUT
CONTACTS
ENERGIZED
ENERGIZED
DE-ENER.
ENERGIZED
ENERGIZED
DE-ENER.
DE-ENER.
CLOSED
DE-ENER.
CLOSED
CLOSED
OPEN
OFF
OPEN
ON
OFF
OPEN
ON
OFF
OFF
ON
ON
DELAY
1
DELAY ACCUMULATION
DELAY 1
DELAY
DELAY
2
OFF AT
ANY TIME
DELAY
DELAY 2
1
www.tycoelectronics.com
Technical support:
Refer to inside back cover.
DELAY
2
AGASTAT
1205