HEDS-5120#C12 Avago Technologies US Inc., HEDS-5120#C12 Datasheet
![Encoders 2 Channel 100CPR](/photos/16/35/163585/heds_5120_sml.jpg)
HEDS-5120#C12
Specifications of HEDS-5120#C12
Related parts for HEDS-5120#C12
HEDS-5120#C12 Summary of contents
Page 1
... HEDS-9700 Small Encoder Module Data Sheet Features: • Codewheels Available in Glass, Film, and Metal • Available in Two Standard Diameters • Cost Effective • Resolutions from 96 CPR to 2048 CPR • For Use with HEDS-90XX/91XX Series Two and Three Channel Encoders • Lead Free ...
Page 2
... Shaft Eccentricity Plus Radial Play Note: Avago Technologies Encoder Modules are guaranteed to 100 kHz, but can operate at higher frequencies. See Encoder Module Data Sheet for specifications and output load recommendations. *HEDM-6140 is guaranteed to 100 kHz with the HEDS-9040 #T00 module. 2 HEDS-XXXX HEDM-XXXX ...
Page 3
... Values are for worst error over a full rotation. Please refer to Encoder Module Data Sheet for definitions of Encoding characteristics. Part Number Description HEDS-51XX Cycle Error Position Error HEDS-61XX Cycle Error Position Error HEDM-512X Cycle Error Position Error HEDM-61XX Cycle Error ...
Page 4
... IMAGE SIDE OF CODEWHEEL Figure 1a. *Please note that the image side of the codewheel must always be facing the module Side A. HEDS-51X0 fig 1a 4 Mounting with Module Side A as the Mounting Plane Mounting a high resolution or three channel encoder with Module Side A as the mounting plane requires alignment pins in the motor base ...
Page 5
... Insert mounting screws through module and thread into the motor base. Do not tighten screws. 4. Slide the HEDS-8905 or HEDS-8906 centering tool over codewheel hub and onto module as shown in Figure 3. The pins of the alignment tool should fit snugly inside the alignment recesses of the module. ...
Page 6
... HEDS-51X0 fig 5 INDEX PULSE REFERENCE MARKER INDEX PULSE 130° ± 5° POSITION TYPICAL R = 11.00 mm (0.433 in.) OP DIMENSIONS IN MM (INCHES) Figure 6. HEDS-5140 Codewheel Used with HEDS-9140. 6 5.94 (0.234) MAX. 1.80 (0.071) MOUNTING BOSS – NOT USED & 1/4" I.D. HUBS 12.70 10 ...
Page 7
... INDEX PULSE REFERENCE MARKER INDEX PULSE POSITION TYPICAL R = 23.36 mm (0.920 in.) OP DIMENSIONS IN MM (INCHES) Figure 7. HEDS-6140 Codewheel Used with HEDS-9040. 0.18 (0.007) 25.56 DIA. ARTWORK SIDE (1.006) MAX. (HEDM-5121) Figure 8. HEDM-5120 Codewheel/HEDM-5121 Codewheel. HEDS-51X0 fig 8 0.18 (0.007) 36.5 50.48 DIA. ARTWORK SIDE (1 ...
Page 8
... MAX. 22.6 MAX. 17.98 MAX. (0.708) ARTWORK SIDE (HEDG-6120) DIMENSIONS IN mm (INCHES) 2-56 SETSCREW USE 0.035" HEX WRENCH 0.18 (0.007) 8.43 (0.332) SETSCREW 22.50 36.5 (0.886) ARTWORK SIDE ARTWORK SIDE (HEDM-6141) (HEDM-6140) DIMENSIONS IN mm (INCHES) HEDS-51X0 fig 12 MAX. ...
Page 9
... Ordering Information Encoder Modules, Codewheel and Assembly Tools Metal Codewheels 0 0 HEDS-9100 Option modules HEDS-5120 HEDS-9140 Option 0 modules HEDS-5140 HEDS-5120 Option codewheels Resolution (Cycles/Rev CPR C - 100 CPR D - 192 CPR E - 200 CPR F - 256 CPR G - 360 CPR H - 400 CPR A - 500 CPR I - 512 CPR ...
Page 10
... Ordering Information (Cont’d HEDS-9000 Option modules HEDS-6100 HEDS-9040 Option 0 modules HEDS-6140 Note: 1. For the lower resolution, two channel encoders, (11 mm ≤ 512 CPR; 23.36 mm ≤ 1024 CPR) the centering tool and gap-setting shim are not necessary, but sometimes helpful in an assembly process. ...
Page 11
... Artwork Orientation Shaft Diameter 0 - Artwork on hub side 06 - 1/4 in. (use when module 08 - 3/8 in. side B is down Artwork opposite hub side (use when module side A is down Assembly Tools Centering Gap-Setting HEDS- HEDS- 8905 8901 Assembly Tools Centering Gap-Setting HEDS- HEDS- 8906 8906 * ...
Page 12
... Option Artwork Orientation Shaft Diameter 0 - Artwork on hub side 06 - 1/4 in. (use when module side B is down Artwork opposite hub side (use when module side A is down Assembly Tools Centering Gap-Setting HEDS- HEDS- 8906 8906 Assembly Tools Centering Gap-Setting HEDS- HEDS- 8905 8932 * ...
Page 13
... Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2009 Avago Technologies. All rights reserved. Obsoletes 5989-0866EN AV02-1450EN - January 21, 2009 Rop = 23.36 mm, 2 HEDG-612 Channels codewheels Option Shaft Diameter www.avagotech.com Assembly Tools Centering HEDS- 8906 * Gap-Setting HEDS- 8932 ...