104068-5 TE Connectivity, 104068-5 Datasheet - Page 3

• Manufacturer Part Number: 104068-5
• Description: Conn Shrouded Header HDR 50 POS 1.27mm Solder ST Thru-Hole Tube
• Manufacturer: TE Connectivity
• Type: Shrouded Headerr

Specifications of 104068-5

• Pitch: 1.27 mm
• Number Of Rows: 2
• Number Of Contacts: 50
• Gender: HDR
• Contact Plating: Gold Over Nickel
• Termination Method: Solder
• Peak Reflow Compatible (260 C): No
• Terminal Type: Straight PCB Thru Hole
• Connector Shroud: Yes
• Body Material: Thermoplastic
• Leaded Process Compatible: No
• Rohs Compliant: No
• Connector Type: Header
• Shrouded: Yes
• Mount Angle: Vertical
• Pcb Mount Style: Through Hole
• Pcb Mount Retention: Without
• Voltage (vac): 30
• Insulation Resistance (m?): 5,000
• Dielectric Withstanding Voltage (v): 500
• Termination Post Length (mm [in]): 2.54 [0.100]
• Solder Tail Contact Plating: Tin-Lead
• Number Of Positions: 50
• Contact Base Material: Phosphor Bronze
• Contact Plating, Mating Area, Material: Gold (30)
• Connector Style: Plug
• Housing Material: Thermoplastic - GF
• Ul Flammability Rating: UL 94V-0
• Housing Color: Black
• Rohs/elv Compliance: ELV compliant, 5 of 6 Compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C, Reflow solder capable to 245°C, Reflow solder capable to 260°C, Pin-in-Paste capable to 245°C, Pin-in-Paste capable to 260°C
• Approved Standards: UL E28476, CSA LR7189
• Temperature Range (°c): -65 – +105
• Packaging Method: Tube

Contact retention.
Coupling torque.
Uncoupling torque.
Dust powder.
Water jet splashing.
Impact.
Thermal shock.
Humidity/temperature cycling.
Rev C
Test Description
1 inch-pound minimum, 15 inch-
pounds maximum with size 17 shell.
1 inch-pound minimum, 15 inch-
pounds maximum with size 17 shell.
See Note.
See Note.
See Note.
See Note.
See Note.
Contact Size
16
8 (Powerband)
Figure 1 (continued)
ENVIRONMENTAL
Requirement
Axial Load
(Lbs Min)
10
25
TE Spec 109-30-2.
Apply axial load to crimped contacts
at the engaging end at a rate of 0.5
inch per minute.
TE Spec 109-42, Condition B.
Measure force necessary to couple
specimens at a maximum rate of 45
degrees rotation per second.
TE Spec 109-42, Condition B.
Measure force necessary to
uncouple specimens at a maximum
rate of 45 degrees rotation per
second.
TE Spec 109-190-2.
TE Spec 109-191-3.
Specimens, wired as intended for
normal service, shall be securely
fastened to the test fixture such that
the specimen can hang freely and
rest against the vertical face of a
1½ to 2 inch thick block of steel that
is sufficiently high and wide to
ensure that the specimen will not
strike near one of the edges of the
block. The specimen shall be
extended its full length from the test
fixture to a horizontal position and
allowed to fall freely by pendulum
action to strike the block. The
distance from the fixture to the
mating end of the specimen shall be
a minimum of 32 inches. There
shall be 8 drops with the radial
orientation for each drop dictated by
using a different index position of
the test fixture.
TE Spec 109-22.
Subject mated specimens to 5
cycles between -55 and 125° C.
TE Spec 109-23-3, Condition B.
Subject mated specimens to 10
cycles between 25 and 65° C at 95%
RH.
Procedure
108-1579
3 of 8