CY7B923-JC Cypress Semiconductor Corp, CY7B923-JC Datasheet - Page 18
![](/photos/31/30/313045/406-28-plcc_sml.jpg)
CY7B923-JC
Manufacturer Part Number
CY7B923-JC
Description
Manufacturer
Cypress Semiconductor Corp
Datasheet
1.CY7B923-JC.pdf
(40 pages)
Specifications of CY7B923-JC
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CY7B923-JC
Manufacturer:
CY
Quantity:
5 530
Part Number:
CY7B923-JC
Manufacturer:
CY
Quantity:
20 000
Receiver Test Mode Description
The CY7B933 receiver offers two types of test mode operation,
BIST mode and Test mode. In a normal system application, the
Built-In Self-Test (BIST) mode can be used to check the function-
ality of the transmitter, the receiver and the link connecting them.
This mode is available with minimal impact on user system logic,
and can be used as part of the normal system diagnostics.
Typical connections and timing are shown in
BIST Mode
The BIST mode function is as follows:
Note A specific test of the RVS output may be required to assure
an adequate test. To perform this test, it is only necessary to have
the transmitter send violation (SVS = HIGH) for a few bytes
before beginning the BIST test sequence. Alternatively, the
receiver could enter BIST mode after the transmitter has begun
sending BIST loop data, or be removed before the transmitter
finishes sending BIST loops, each of which contain several delib-
erate violations and should cause RVS to pulse HIGH.
BIST mode is intended to check the entire function of the Trans-
mitter, serial link, and receiver. It augments normal factory ATE
testing and provides the user system with a rigorous test
mechanism to check the link transmission system, without
requiring any significant system overhead.
When in bypass mode, the BIST logic will function in the same
way as in the encoded mode. MODE = HIGH and BISTEN =
LOW causes the receiver to switch to encoded mode and begin
checking the decoded received data of the BIST pattern, as if
MODE = LOW. When BISTEN returns to HIGH, the receiver
resumes normal bypass operation. In test mode the BIST
function works as in the normal mode.
Test Mode
The MODE input pin selects between three receiver functional
modes. When wired to VCC, the shifter contents bypass the
decoder and go directly from the decoder latch to the Q
of the output latch. When wired to GND, the outputs are decoded
using the 8B/10B codes shown at the end of this datasheet and
become Q
used for factory or incoming device test. This mode can be
selected by leaving the MODE pin open (internal circuitry forces
the open pin to V
Test mode causes the Receiver to function in its Encoded mode,
but with INB (INB+) as the bit rate Test clock instead of the
Internal PLL generated bit clock. In this mode, transfers between
the Shifter, Decoder register and Output register are controlled
by their normal logic, but with an external bit rate clock instead
of the PLL (the recovered bit clock). Internal logic and test pattern
Document #: 38-02017 Rev. *H
1. Set BISTEN LOW to enable self-test generation and await
2. Monitor RVS and check for any byte time with the pin HIGH
3. When testing is completed, set BISTEN HIGH and resume
RDY LOW indicating that the initialization code has been re-
ceived.
to detect pattern mismatches. RDY will pulse HIGH once per
BIST loop, and can be used by an external counter to monitor
test pattern progress. Q
pattern and may be useful for debug purposes.
normal function.
0–7
, RVS, and SC/D. The third function is test mode,
CC
/2).
0–7
and SC/D will show the expected
Figure 8 on page
a–j
inputs
15.
inputs can be synchronized by sending a SYNC pattern and
allowing the Framer to align the logic to the bit stream. The flow
is as follows:
(While in Test mode and in BIST mode with RF HIGH, the Q
RVS, and SC/D outputs reflect various internal logic states and
not the received data.)
Test mode is intended to allow logical, DC, and AC testing of the
Receiver without requiring that the tester generate input data at
the bit rate or accommodate the PLL lock, tracking and
frequency range characteristics that are required when the part
operates in its normal mode.
X3.230 Codes and Notation Conventions
Information to be transmitted over a serial link is encoded eight
bits at a time into a 10-bit Transmission Character and then sent
serially, bit by bit. Information received over a serial link is
collected ten bits at a time, and those Transmission Characters
that are used for data (Data Characters) are decoded into the
correct eight-bit codes. The 10-bit Transmission Code supports
all 256 8-bit combinations. Some of the remaining Transmission
Characters (Special Characters) are used for functions other
than data transmission.
The primary rationale for use of a Transmission Code is to
improve the transmission characteristics of a serial link. The
encoding defined by the Transmission Code ensures that suffi-
cient transitions are present in the serial bit stream to make clock
recovery possible at the Receiver. Such encoding also greatly
increases the likelihood of detecting any single or multiple bit
errors that may occur during transmission and reception of infor-
mation. In addition, some Special Characters of the Trans-
mission Code selected by Fibre Channel Standard consist of a
distinct and easily recognizable bit pattern (the Special Character
Comma) that assists a Receiver in achieving word alignment on
the incoming bit stream.
Notation Conventions
The documentation for the 8B/10B Transmission Code uses
letter notation for the bits in an 8-bit byte. Fibre Channel Standard
notation uses a bit notation of A, B, C, D, E, F, G, H for the 8-bit
byte for the raw 8-bit data, and the letters a, b, c, d, e, i, f, g, h, j
for encoded 10-bit data. There is a correspondence between bit
A and bit a, B and b, C and c, D and d, E and e, F and f, G and
g, and H and h. Bits i and j are derived, respectively, from
(A,B,C,D,E) and (F,G,H).
The bit labeled A in the description of the 8B/10B Transmission
Code corresponds to bit 0 in the numbering scheme of the FC-2
specification, B corresponds to bit 1, as shown below.
FC-2 bit designation—
HOTLink D/Q designation— 7
8B/10B bit designation— H
1. Assert Test mode for several test clock cycles to establish
2. Assert RF to enable reframing.
3. Input a repeating sequence of bits representing K28.5 (Sync).
4. RDY falling shows the byte boundary established by the
5. Proceed with pattern, voltage and timing tests as is conve-
normal counter sequence.
K28.5 input pattern.
nient for the test program and tester to be used.
7
CY7B923, CY7B933
6 5
6 5
G F
4
4
E
3
3
D
2
2
C
Page 18 of 40
1
1
B
0
0
A
0–7
,
[+] Feedback