HC55185GCRZ Intersil, HC55185GCRZ Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
HC55185GCRZ
Manufacturer Part Number
HC55185GCRZ
Description
Manufacturer
Intersil
Datasheet
1.HC55185GCRZ.pdf
(20 pages)
Specifications of HC55185GCRZ
Number Of Channels
1
On-hook Transmission
Yes
Polarity Reversal
Yes
On-chip Ring Relay Driver
Yes
Operating Supply Voltage (typ)
5/-18/-24/-28V
Operating Temp Range
0C to 85C
Loop Current Limit
45mA
Operating Temperature Classification
Commercial
Pin Count
32
Mounting
Surface Mount
Operating Current
10.3mA
Operating Supply Voltage (max)
5.25/-52V
Operating Supply Voltage (min)
4.75/-16V
Lead Free Status / RoHS Status
Compliant
Since the current relationships are different for constant
current versus constant voltage, the region of device
operation is critical to valid power dissipation calculations.
Reverse Active
Overview
The reverse active mode (RA, 011) provides the same
functionality as the forward active mode. On hook
transmission, DC loop feed and voice transmission are
supported. Loop supervision is provided by either the switch
hook detector (E0 = 1) or the ground key detector (E0 = 0).
The device may be operated from either high or low battery.
During reverse active the Tip and Ring DC voltage
characteristics exchange roles. That is, Ring is typically 4V
below ground and Tip is typically 4V more positive than
battery. Otherwise, all feed and voice transmission
characteristics are identical to forward active.
Silent Polarity Reversal
Changing from forward active to reverse active or vice versa
is referred to as polarity reversal. Many applications require
slew rate control of the polarity reversal event. Requirements
range from minimizing cross talk to protocol signalling.
The device uses an external low voltage capacitor, C
set the reversal time. Once programmed, the reversal time
will remain nearly constant over various load conditions. In
addition, the reversal timing capacitor is isolated from the AC
loop, therefore loop stability is not impacted.
The internal circuitry used to set the polarity reversal time is
shown below.
During forward active, the current from source I1 charges
the external timing capacitor C
The internal resistor provides a clamping function for
voltages on the POL node. During reverse active, the switch
closes and I2 (roughly twice I1) pulls current from I1 and the
timing capacitor. The current at the POL node provides the
drive to a differential pair which controls the reversal time of
the Tip and Ring DC voltages.
Where Δtime is the required reversal time. Polarized
capacitors may be used for C
C
POL
=
75kΩ
Δtime
----------------
75000
FIGURE 9. REVERSAL TIMING CONTROL
13
POL
POL
I
I
1
2
. The low voltage at the
and the switch is open.
POL
C
POL
POL
(EQ. 32)
, to
HC55185
POL pin and minimal voltage excursion ±0.75V, are well
suited to polarized capacitors.
Power Dissipation
The power dissipation equations for forward active operation
also apply to the reverse active mode.
Ringing
Overview
The ringing mode (RNG,100) provides linear amplification to
support a variety of ringing waveforms. A programmable ring
trip function provides loop supervision and auto disconnect
upon ring trip. The device is designed to operate from the
high battery during this mode.
Architecture
The device provides linear amplification to the signal applied
to the ringing input, V
device is 80V/V. The circuit model for the ringing path is
shown in Figure 10.
The voltage gain from the VRS input to the Tip output is
40V/V. The resistor ratio provides a gain of 8 and the current
mirror provides a gain of 5. The voltage gain from the VRS
input to the Ring output is -40V/V. The equations for the Tip
and Ring outputs during ringing are provided below.
When the input signal at VRS is zero, the Tip and Ring
amplifier outputs are centered at half battery. The device
provides auto centering for easy implementation of
sinusoidal ringing waveforms. Both AC and DC control of the
Tip and Ring outputs is available during ringing. This feature
allows for DC offsets as part of the ringing waveform.
Ringing Input
The ringing input, V
impedance allows the use of low value capacitors for AC
coupling the ring signal. The V
during the ringing mode, therefore a free running oscillator
may be connected to VRS at all times.
V
V
RING
T
R
TIP
=
=
V
-----------
V
-----------
BH
2
BH
2
+
–
20
20
(
(
FIGURE 10. LINEAR RINGING MODEL
40
40
×
×
R
R
VRS
VRS
+
+
-
-
RS
)
)
RS
, is a high impedance input. The high
. The differential ringing gain of the
+
-
V
BH
2
RS
5:1
input is enabled only
R/8
600k
December 18, 2006
+
-
(EQ. 33)
FN4831.14
(EQ. 34)
VRS