MCP6V06T-E/SN Microchip Technology, MCP6V06T-E/SN Datasheet - Page 26

• Manufacturer Part Number: MCP6V06T-E/SN
• Description: Single, Auto-Zero Op Amp, E Temp 8 SOIC 3.90mm (.150") T/R
• Manufacturer: Microchip Technology

Specifications of MCP6V06T-E/SN

• Amplifier Type: Chopper (Zero-Drift)
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Slew Rate: 0.5 V/µs
• Gain Bandwidth Product: 1.3MHz
• Current - Input Bias: 6pA
• Voltage - Input Offset: 3µV
• Current - Supply: 300µA
• Current - Output / Channel: 22mA
• Voltage - Supply, Single/dual (±): 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Number Of Channels: 1
• Voltage Gain Db: 158 dB
• Common Mode Rejection Ratio (min): 120 dB
• Input Offset Voltage: 0.003 mV
• Operating Supply Voltage: 3 V, 5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Details
• Other names: MCP6V06T-E/SNTR

MCP6V06/7/8
4.3.9
In order to achieve DC precision on the order of ±1 µV,
many physical errors need to be minimized. The design
of the Printed Circuit Board (PCB), the wiring, and the
thermal environment has a strong impact on the
precision achieved. A poor PCB design can easily be
more than 100 times worse than the MCP6V06/7/8 op
amps minimum and maximum specifications.
4.3.9.1
Any time two dissimilar metals are joined together, a
temperature dependent voltage appears across the
junction (the Seebeck or thermo-junction effect). This
effect is used in thermocouples to measure tempera-
ture. The following are examples of thermo-junctions
on a PCB:
• Components (resistors, op amps, …) soldered to
• Wires mechanically attached to the PCB
• Jumpers
• Solder joints
• PCB vias
Typical thermo-junctions have temperature to voltage
conversion coefficients of 10 to 100 µV/°C (sometimes
higher).
There are three basic approaches to minimizing
thermo-junction effects:
• Minimize thermal gradients
• Cancel thermo-junction voltages
• Minimize difference in thermal potential between
DS22093B-page 26
a copper pad
metals
PCB DESIGN FOR DC PRECISION
Thermo-junctions
4.3.9.2
Figure 4-11
and inverting gain amplifier circuits on one schematic.
Usually, to minimize the input bias current related off-
set, R
The guard traces (with ground vias at the ends) help
minimize the thermal gradients. The resistor layout
cancels the resistor thermal voltages, assuming the
temperature gradient is constant near the resistors:
EQUATION 4-2:
FIGURE 4-11:
for Single Non-inverting and Inverting Amplifiers.
Where:
Note:
V
V
G
G
1
M
P
M
P
is chosen to be R
V
V
=
=
M
P
Changing the orientation of the resistors
will usually cause a significant decrease in
the cancellation of the thermal voltages.
shows the recommended non-inverting
V
MCP6V06
Non-inverting and Inverting Amplifier
Layout for Thermo-junctions
OUT
R
1 + G
magnitude
V
R3
R2
R1
OS
3
/R
R
R
≈ -V
≈ V
1
2
is neglected
2
M
U
, inverting gain magnitude
P
, non-inverting gain
PCB Layout and Schematic
1
M
G
© 2008 Microchip Technology Inc.
G
2
P
||R
,
M
, V
R
3
.
3
V
U1
M
P
= GND
= GND
V
OUT
V
OUT