MCP6V06T-E/SN Microchip Technology, MCP6V06T-E/SN Datasheet - Page 29

• Manufacturer Part Number: MCP6V06T-E/SN
• Description: Single, Auto-Zero Op Amp, E Temp 8 SOIC 3.90mm (.150") T/R
• Manufacturer: Microchip Technology

Specifications of MCP6V06T-E/SN

• Amplifier Type: Chopper (Zero-Drift)
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Slew Rate: 0.5 V/µs
• Gain Bandwidth Product: 1.3MHz
• Current - Input Bias: 6pA
• Voltage - Input Offset: 3µV
• Current - Supply: 300µA
• Current - Output / Channel: 22mA
• Voltage - Supply, Single/dual (±): 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Number Of Channels: 1
• Voltage Gain Db: 158 dB
• Common Mode Rejection Ratio (min): 120 dB
• Input Offset Voltage: 0.003 mV
• Operating Supply Voltage: 3 V, 5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Details
• Other names: MCP6V06T-E/SNTR

4.4
4.4.1
Many sensors are configured as Wheatstone bridges.
Strain gauges and pressure sensors are two common
examples. These signals can be small and the
common mode noise large. Amplifier designs with high
differential gain are desirable.
Figure 4-15
bridge with a minimum of components. Because the
circuit is not symmetric, the ADC input is single ended,
and there is a minimum of filtering, the CMRR is good
enough for moderate common mode noise.
FIGURE 4-15:
Figure 4-16
Wheatstone bridges. This circuit is symmetric and has
high CMRR. Using a differential input to the ADC helps
with the CMRR.
FIGURE 4-16:
© 2008 Microchip Technology Inc.
R R
R R
R R
R R
V
Typical Applications
DD
WHEATSTONE BRIDGE
shows how to interface to a Wheatstone
shows a higher performance circuit for
10 nF
10 nF
V
DD
0.2R
0.2R
Simple Design.
High Performance Design.
1 µF
200Ω
200Ω
200 Ω
200 Ω
0.01C
100R
MCP6V06
20 kΩ
20 kΩ
3 kΩ
1 µF
1 µF
3 kΩ
3 kΩ
½ MCP6V07
½ MCP6V07
ADC
V
DD
ADC
V
DD
4.4.2
The ratiometric circuit in
wire RTD. It corrects for the sensor’s wiring resistance
by subtracting the voltage across the middle R
top R1 does not change the output voltage; it balances
the op amp inputs. Failure (open) of the RTD is
detected by an out-of-range voltage.
FIGURE 4-17:
The voltages at the input of the ADC can be calculated
with the following:
Where:
R
R
R
V
V
R
100Ω
W
W
W
V
V
CM
DM
V
G
RTD
W
V
V
B
T
RTD
G
DM
CM
W
RTD SENSOR
=
=
=
=
=
=
=
=
=
10 nF
10 nF
1
G
G
V
------------------------------------------------------------------------------
V
T
+
RTD
RTD
DD
+
MCP6V06/7/8
2 R
Voltage at the top of R
Voltage at the bottom of R
Voltage across top and middle
R
ADC’s common mode input
ADC’s differential mode input
R
20 kΩ
R
20 kΩ
V
⋅
(
W
–
T
B
V
RTD Sensor.
B
’s
1 µF
R
2.49 kΩ
2.49 kΩ
T
3
Figure 4-17
+
2.49 kΩ
2.49 kΩ
3
–
⁄
(
R
R
R
⁄
V
G
R
2
1
1
B
1
RTD
)
2
+
G
+
W
R
2.55 kΩ
R
2.55 kΩ
1 G
100 kΩ
100 kΩ
100 nF
100 nF
DS22093B-page 29
conditions a three
V
2
2
–
R
R
W
3
3
½ MCP6V07
½ MCP6V07
W
)V
RTD
W
RTD
3 kΩ
3 kΩ
ADC
W
V
. The
DD