PIC24FJ16GA002-E/SO Microchip Technology, PIC24FJ16GA002-E/SO Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC24FJ16GA002-E/SO
Manufacturer Part Number
PIC24FJ16GA002-E/SO
Description
16-bit Family, 16 MIPS, 16KB Flash, 4096 Bytes RAM, 21 I/O, NanoWatt 28 SOIC .30
Manufacturer
Microchip Technology
Series
PIC® 24Fr
Datasheets
1.PIC24FJ16GA002-ISS.pdf
(52 pages)
2.PIC24FJ16GA002-ISS.pdf
(268 pages)
3.PIC24FJ16GA002-ISS.pdf
(22 pages)
Specifications of PIC24FJ16GA002-E/SO
Core Processor
PIC
Core Size
16-Bit
Speed
32MHz
Connectivity
I²C, PMP, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
21
Program Memory Size
16KB (5.5K x 24)
Program Memory Type
FLASH
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 10x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
28-SOIC (7.5mm Width)
Processor Series
PIC24FJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
4 KB
Interface Type
I2C, IrDA, SPI, UART
Maximum Clock Frequency
32 MHz
Number Of Programmable I/os
21
Number Of Timers
5
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM240011, MA240013, AC164127, DM300027, DV164033, DM240002
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 10 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DM240011 - KIT STARTER MPLAB FOR PIC24F MCUAC162088 - HEADER MPLAB ICD2 24FJ64GA004 28AC164339 - MODULE SKT FOR PM3 28SOICDV164033 - KIT START EXPLORER 16 MPLAB ICD2
Eeprom Size
-
Lead Free Status / Rohs Status
Details
PIC24FJ64GA004 FAMILY
19. Module: SPI
DS80470E-page 8
In SPI Slave mode (MSTEN = 0), with the slave
select option enabled (SSEN = 1), the peripheral
may accept transfers regardless of the SSx pin
state. The received data in SPIxBUF will be
accurate but not intended for the device.
Work around
There is a work around using the Peripheral Pin
Select (PPS) feature. One of the external inter-
rupts (INT1 or INT2) can be mapped to the same
pin as the SSx signal or the SSx signal can be
mapped to a pin with interrupt-on-change (CNx)
functionality. If the SSx signal changes to low
(active), the interrupt flag will be set.
When an SPI data received interrupt occurs, the
interrupt flag can be tested. If the interrupt mapped
to SSx did not occur, discard the data.
Affected Silicon Revisions
A3/
A4
X
B4
B5
B8
20. Module: SPI
When using Enhanced Buffer mode, an interrupt
will not occur if the following conditions exist:
• SPI Buffer Interrupt mode, SISEL<2:0>
• Slave Select mode is enabled (SSEN = 1).
This only occurs when Enhanced mode, Slave
Select mode and interrupt on Shift register empty
are all enabled. In other modes, the interrupt will
work correctly.
Work around
When Slave Select mode is enabled, interrupting
on SPIxSR empty and TX empty will occur at the
same time. Therefore, interrupting on TX FIFO
empty (SISEL<2:0> = 110) can be used as an
alternative to interrupting when the Shift register is
empty (SISEL<2:0> = 101).
Affected Silicon Revisions
A3/
A4
(SPIxSTAT<4:2>), is set to interrupt when the
Shift register is empty (SISEL<2:0> = 101).
X
B4
B5
2010 Microchip Technology Inc.
B8