PIC24FJ256DA210T-I/BG Microchip Technology, PIC24FJ256DA210T-I/BG Datasheet - Page 5

• Manufacturer Part Number: PIC24FJ256DA210T-I/BG
• Description: 16-bit, 256KB Flash, 96K RAM, USB, Graphics 121 XBGA 10x10x1.20mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ256DA210T-I/BG

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, GFX, LVD, POR, PWM, WDT
• Number Of I /o: 84
• Program Memory Size: 256KB (85.5K x 24)
• Program Memory Type: FLASH
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 121-TFBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Data Sheet Clarifications
The following typographic corrections and clarifications
are to be noted for the latest version of the device data
sheet (DS39969B):
1. Module: Guidelines for Getting Started
Section 2.4 Voltage Regulator Pins (ENVREG/DIS-
VREG and V
new and more detailed section. The entire text follows:
2.4
The on-chip voltage regulator enable pin must always
be connected directly to a supply voltage.
Refer to Section 27.2 “On-Chip Voltage Regulator”
for details on connecting and using the on-chip
regulator.
TABLE 2-1
 2011 Microchip Technology Inc.
Note:
Panasonic
Panasonic
Murata
Murata
Make
TDK
TDK
Voltage Regulator Pins (ENVREG/
DISVREG and V
Corrections are shown in bold. Where
possible, the original bold text formatting
has been removed for clarity.
CAP
with 16-Bit Microcontrollers
/V
SUITABLE CAPACITOR EQUIVALENTS
GRM32DR71C106KA01L
GRM31CR61C106KC31L
DDCORE
C3216X7R1C106K
C3216X5R1C106K
ECJ-3YX1C106K
ECJ-4YB1C106K
) has been replaced with a
Part #
CAP
/V
DDCORE
)
PIC24FJ256DA210 FAMILY
Capacitance
Nominal
10 µF
10 µF
10 µF
10 µF
10 µF
10 µF
When the regulator is enabled, a low-ESR (< 5Ω)
capacitor is required on the V
voltage regulator output voltage. The V
be connected to V
connected to ground. The type can be ceramic or
tantalum. Suitable examples of capacitors are shown in
Table
be used.
Designers may use
equivalence of candidate devices.
The placement of this capacitor should be close to
V
exceed 0.25 inch (6 mm). Refer to Section 30.0
“Electrical
information.
FIGURE 2-3
CAP
Base Tolerance Rated Voltage Temp. Range
0.001
Note:
0.01
0.1
. It is recommended that the trace length not
10
2-1. Capacitors with equivalent specifications can
1
0.01
±10%
±10%
±10%
±10%
±10%
±10%
Typical data measurement at 25°C, 0V DC bias.
0.1
Characteristics”
DD
Frequency (MHz)
and must use a capacitor of 10 µF
FREQUENCY vs. ESR
PERFORMANCE FOR
SUGGESTED V
1
Figure 2-3
16V
16V
16V
16V
16V
16V
10
CAP
pin to stabilize the
to evaluate ESR
100
for
DS80505C-page 5
CAP
-55 to 125ºC
-55 to 125ºC
-55 to 125ºC
-55 to 85ºC
-55 to 85ºC
-55 to 85ºC
CAP
1000 10,000
pin must not
additional