PIC24HJ32GP202-E/SO Microchip Technology, PIC24HJ32GP202-E/SO Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC24HJ32GP202-E/SO
Manufacturer Part Number
PIC24HJ32GP202-E/SO
Description
16-bit MCU, 32KB Flash,40 MIPS,nanoWatt 28 SOIC .300in TUBE
Manufacturer
Microchip Technology
Series
PIC® 24Hr
Datasheets
1.PIC24HJ12GP201-ISO.pdf
(84 pages)
2.PIC24HJ32GP202-ISO.pdf
(272 pages)
3.PIC24HJ32GP202-ISO.pdf
(8 pages)
4.PIC24HJ32GP202-ISO.pdf
(12 pages)
Specifications of PIC24HJ32GP202-E/SO
Core Processor
PIC
Core Size
16-Bit
Speed
40 MIPs
Connectivity
I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
21
Program Memory Size
32KB (11K x 24)
Program Memory Type
FLASH
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 10x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
28-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164339 - MODULE SKT FOR PM3 28SOIC
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
PIC24HJ32GP202/204 and PIC24HJ16GP304
Silicon Errata Issues
1. Module: JTAG
2. Module: UART
3. Module: UART
DS80467E-page 4
Note:
JTAG programming does not work.
Work around
None.
Affected Silicon Revisions
The auto-baud feature may not calculate the correct
baud rate when the High Baud Rate Enable bit,
BRGH, is set. With the BRGH bit set, the baud rate
calculation used is the same as BRG = 0.
Work around
If the auto-baud feature is needed, use the Low
Baud Rate mode by clearing the BRGH bit.
Affected Silicon Revisions
With the auto-baud feature selected, the Sync
Break character (0x55) may be loaded into the
FIFO as data.
Work around
To prevent the Sync Break character from being
loaded into the FIFO, load the UxBRG register with
either 0x0000 or 0xFFFF prior to enabling the
auto-baud feature (ABAUD = 1).
Affected Silicon Revisions
A2
A2
A2
X
X
X
This document summarizes all silicon
errata issues from all revisions of silicon,
previous as well as current. Only the
issues indicated by the shaded column in
the following tables apply to the current
silicon revision (A6).
A3
A3
A3
X
X
X
A4
A4
A4
X
X
X
A5
A5
A5
X
X
X
A6
A6
A6
X
X
X
4. Module: UART
5. Module: UART
6. Module: UART
The auto-baud feature may miscalculate for
certain baud rate and clock speed combinations,
resulting in a BRG value that is greater than or less
than the expected value by 1. This may result in
reception or transmission failures.
Work around
Test the auto-baud rate at various clock speed and
baud rate combinations that would be used in an
application. If an inaccurate BRG value is
generated, manually correct the baud rate in user
software.
Affected Silicon Revisions
When an auto-baud is detected, the receive
interrupt may occur twice. The first interrupt occurs
at the beginning of the Start bit and the second
after reception of the Sync field character.
Work around
If an extra interrupt is detected, ignore the
additional interrupt.
Affected Silicon Revisions
When the UART is configured for IR interface
operations (UxMODE<9:8> = 11), the 16x baud
clock signal on the BCLK pin is present only when
the module is transmitting. The pin is idle at all
other times.
Work around
Configure one of the output compare modules to
generate the required baud clock signal when the
UART is receiving data or in an Idle state.
Affected Silicon Revisions
A2
A2
A2
X
X
X
A3
A3
A3
X
X
X
A4
A4
A4
X
X
X
© 2010 Microchip Technology Inc.
A5
A5
A5
X
X
X
A6
A6
A6
X
X
X