PIC24HJ32GP202-H/MM Microchip Technology, PIC24HJ32GP202-H/MM Datasheet

16-bit MCU, 32KB Flash,40 MIPS,nanoWatt 28 QFN-S 6x6mm TUBE

PIC24HJ32GP202-H/MM

Manufacturer Part Number
PIC24HJ32GP202-H/MM
Description
16-bit MCU, 32KB Flash,40 MIPS,nanoWatt 28 QFN-S 6x6mm TUBE
Manufacturer
Microchip Technology
Series
PIC® 24Hr

Specifications of PIC24HJ32GP202-H/MM

Core Processor
PIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
21
Program Memory Size
32KB (11K x 24)
Program Memory Type
FLASH
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 10x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 140°C
Package / Case
28-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The PIC24HJ32GP202/204 and PIC24HJ16GP304
(Rev. A2/A3/A4) devices you received were found to
conform to the
described in the following documents:
• DS70289 – “PIC24HJ32GP202/204 and
• DS70157 – “dsPIC30F/33F Programmer’s
The exceptions to the specifications in the documents
listed above are described in this section. The specific
devices for which these exceptions are described are
listed below:
• PIC24HJ32GP202
• PIC24HJ32GP204
• PIC24HJ16GP304
PIC24HJ32GP202/204 and PIC24HJ16GP304 Rev.
A2/A3/A4 silicon is identified by performing a “Reset
and Connect” operation to the device using MPLAB
ICD 2 or MPLAB REAL ICE™ in-circuit emulator, with
MPLAB IDE v7.60 or later. The output window will show
a successful connection to the device specified in
Configure>Select Device. The resulting DEVREV
register values for Rev. A2/A3/A4 silicon are 0x3001,
0x3002 and 0x3003, respectively.
The errata described in this document will be
addressed in future revisions of silicon.
© 2008 Microchip Technology Inc.
PIC24HJ16GP304 Data Sheet”
Reference Manual”
PIC24HJ32GP202/204 and PIC24HJ16GP304
specifications and functionality
Rev. A2/A3/A4 Silicon Errata
PIC24HJ32GP202/204 and
®
Silicon Errata Summary
The following list summarizes the errata described in
further detail through the remainder of this document:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. I
JTAG Programming
JTAG programming does not work.
UART Module
The auto-baud feature may not calculate the
correct baud rate when the Baud Rate Generator
(BRG) is set up for 4x mode.
UART Module
With the auto-baud feature selected, the Sync
Break character (0x55) may be loaded into the
FIFO as data.
UART Module
The auto-baud feature measures baud rate
inaccurately for certain baud rate and clock speed
combinations.
UART Module
When an auto-baud is detected, the receive
interrupt may occur twice.
UART Module
The 16x baud clock signal on the BCLK pin is
present only when the module is transmitting.
UART Module
When the UART is in 4x mode (BRGH = 1) and
using two Stop bits (STSEL = 1), it may sample the
first Stop bit instead of the second one.
SPI Module
The SPIxCON1 DISSCK bit does not influence
port functionality.
I
The BCL bit in I2CSTAT can be cleared only with
16-bit operation and can be corrupted with 1-bit or
8-bit operations on I2CSTAT.
The ACKSTAT bit is cleared shortly after being set
following a slave transmit.
2
2
C™ Module
C Module
PIC24HJ16GP304
DS80339D-page 1

Related parts for PIC24HJ32GP202-H/MM

PIC24HJ32GP202-H/MM Summary of contents

Page 1

... The PIC24HJ32GP202/204 and PIC24HJ16GP304 (Rev. A2/A3/A4) devices you received were found to conform to the specifications and functionality described in the following documents: • DS70289 – “PIC24HJ32GP202/204 and PIC24HJ16GP304 Data Sheet” • DS70157 – “dsPIC30F/33F Programmer’s Reference Manual” The exceptions to the specifications in the documents listed above are described in this section ...

Page 2

... When an auto-baud is detected, the receive interrupt may occur twice. The first interrupt occurs at the beginning of the Start bit and the second after reception of the Sync field character. Work around If an extra interrupt is detected, ignore the additional interrupt. © 2008 Microchip Technology Inc. ...

Page 3

... ACKSTAT bit is set it will be cleared again after some delay. Work around Store the value of the ACKSTAT bit immediately 2 after interrupt occurs. © 2008 Microchip Technology Inc. 2 11. Module there are two I C devices on the bus, one of them is acting as the Master receiver and the other as the Slave transmitter ...

Page 4

... Work around Ensure that the lower address byte in 10-bit Addressing mode does not match any 7-bit reserved addresses module enabled, the PORT bits and interrupt input functions (if any module and with the XX1111XXXX, © 2008 Microchip Technology Inc. ...

Page 5

... Added silicon issues 6-7 (UART), 8 (SPI), 9-11 (I and 12 (Product Identification). Revision D (9/2008) Added reference to silicon revision A4. Updated silicon issue 12 (Product Identification). Added silicon issues 13 (UART (UxE Interrupt)), 14 (UART (IrDA)), 15 (Inter- nal Voltage Regulator), 16 (PSV Operations) and 17-19 (I2C). © 2008 Microchip Technology Inc DS80339D-page 5 ...

Page 6

... NOTES: DS80339D-page 6 © 2008 Microchip Technology Inc. ...

Page 7

... PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...

Page 8

... Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2008 Microchip Technology Inc. 01/02/08 ...

Related keywords