S29GL032M10TAIR40 Spansion Inc., S29GL032M10TAIR40 Datasheet - Page 2

• Manufacturer Part Number: S29GL032M10TAIR40
• Description: IC,EEPROM,NOR FLASH,2MX16/4MX8,CMOS,TSSOP,48PIN,PLASTIC
• Manufacturer: Spansion Inc.

General Description
2
The S29GL256/128/064/032M family of devices are 3.0 V single power Flash
memory manufactured using 0.23 um MirrorBit technology. The S29GL256M is a
256 Mbit, organized as 16,777,216 words or 33,554,432 bytes. The S29GL128M
is a 128 Mbit, organized as 8,388,608 words or 16,777,216 bytes. The
S29GL064M is a 64 Mbit, organized as 4,194,304 words or 8,388,608 bytes. The
S29GL032M is a 32 Mbit, organized as 2,097,152 words or 4,194,304 bytes. De-
pending on the model number, the devices have an 8-bit wide data bus only, 16-
bit wide data bus only, or a 16-bit wide data bus that can also function as an 8-
bit wide data bus by using the BYTE# input. The devices can be programmed ei-
ther in the host system or in standard EPROM programmers.
Access times as fast as 90 ns (S29GL128M, S29GL064M, S29GL032M) or 100 ns
(S29GL256M) are available. Note that each access time has a specific operating
voltage range (V
Information
TSOP, 48-ball fine-pitch BGA, 63-ball fine-pitch BGA and 64-ball Fortified BGA,
depending on model number. Each device has separate chip enable (CE#), write
enable (WE#) and output enable (OE#) controls.
Each device requires only a single 3.0 volt power supply for both read and
write functions. In addition to a V
(ACC) feature provides shorter programming times through increased current on
the WP#/ACC input. This feature is intended to facilitate factory throughput dur-
ing system production, but may also be used in the field if desired.
The device is entirely command set compatible with the JEDEC single-power-
supply Flash standard. Commands are written to the device using standard mi-
croprocessor write timing. Write cycles also internally latch addresses and data
needed for the programming and erase operations.
The sector erase architecture allows memory sectors to be erased and repro-
grammed without affecting the data contents of other sectors. The device is fully
erased when shipped from the factory.
Device programming and erasure are initiated through command sequences.
Once a program or erase operation has begun, the host system need only poll the
DQ7 (Data# Polling) or DQ6 (toggle) status bits or monitor the Ready/Busy#
(RY/BY#) output to determine whether the operation is complete. To facilitate
programming, an Unlock Bypass mode reduces command sequence overhead
by requiring only two write cycles to program data instead of four.
Hardware data protection measures include a low V
ically inhibits write operations during power transitions. The hardware sector
protection feature disables both program and erase operations in any combina-
tion of sectors of memory. This can be achieved in-system or via programming
equipment.
The Erase Suspend/Erase Resume feature allows the host system to pause an
erase operation in a given sector to read or program any other sector and then
complete the erase operation. The Program Suspend/Program Resume fea-
ture enables the host system to pause a program operation in a given sector to
read any other sector and then complete the program operation.
The hardware RESET# pin terminates any operation in progress and resets the
device, after which it is then ready for a new operation. The RESET# pin may be
tied to the system reset circuitry. A system reset would thus also reset the device,
sections. Package offerings include 40-pin TSOP, 48-pin TSOP, 56-pin
CC
) as specified in the
S29GLxxxM MirrorBit
CC
input, a high-voltage accelerated program
P r e l i m i n a r y
Product Selector Guide
TM
Flash Family
CC
detector that automat-
and the
Ordering
S29GLxxxM_00A5 April 30, 2004