HB28K032MM3 Renesas Electronics America, HB28K032MM3 Datasheet - Page 6
HB28K032MM3
Manufacturer Part Number
HB28K032MM3
Description
Manufacturer
Renesas Electronics America
Type
MultiMedia Cardr
Datasheet
1.HB28K032MM3.pdf
(91 pages)
Specifications of HB28K032MM3
Density
32MByte
Operating Supply Voltage (typ)
3.3V
Operating Temperature (min)
-25C
Operating Temperature (max)
85C
Package Type
Not Required
Mounting
Surface Mount
Pin Count
7
Operating Temperature Classification
Commercial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Programmable
Yes
Lead Free Status / RoHS Status
Compliant
- Current page: 6 of 91
- Download datasheet (527Kb)
HB28K032/L064/J128/J256/J512MM3, HB28K032/L064/J128/J256RM3
SPI Mode
The Serial Peripheral Interface (SPI) is a general-purpose synchronous serial interface originally found on
certain Motorola microcontrollers. The MultiMediaCard SPI interface is compatible with SPI hosts
available on the market. As any other SPI device the MultiMediaCard SPI interface consists of the
following four signals:
CS: Host to card Chip Select signal.
CLK: Host to card clock signal.
Data in: Host to card data signal.
Data out: Card to host data signal.
The MultiMediaCard card identification and addressing methods are replaced by a hardware Chip Select
(CS) signal. There are no broadcast commands. For every command, a card (slave) is selected by
asserting (active low) the CS signal (refer to Figure “SPI Bus System”). The CS signal must be
continuously active for the duration of the SPI transaction (command, response and data). The only
exception occurs during card programming, when the host can de-assert the CS signal without affecting the
programming process. The bidirectional CMD and DAT lines are replaced by unidirectional data in and
data out signals. This eliminates the ability of executing commands while data is being read or written and,
therefore, makes the sequential and multi block read/write operations obsolete. The single and multiple
block read/write commands are supported by the SPI channel. The SPI interface uses the same seven
signals of the standard MultiMediaCard bus (refer to Table “SPI Interface Pin Configuration”).
Rev.0.02, Sep.15.2004, page 6 of 89
Power
supply
SPI bus (CLK, Datain, Dataout)
SPI card
SPI Bus System
SPI card
SPI bus master
CS
CS
Related parts for HB28K032MM3
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PWR SPLY LINEAR SINGLE 28V@1A
Manufacturer:
SL Power Electronics Manufacture of Condor/Ault Brands
Datasheet:
Part Number:
Description:
LINEAR SUPPLY 28V/1.0A OUTPUT
Manufacturer:
POWER ONE
Datasheet:
Part Number:
Description:
PWR SPLY LINEAR SINGLE 28V@1A
Manufacturer:
SL Power Electronics Manufacture of Condor/Ault Brands
Datasheet:
Part Number:
Description:
LINEAR SUPPLY 28V/1.0A OUTPUT
Manufacturer:
POWER ONE
Datasheet:
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet: