AFCT-5715PZ-JU1 Avago Technologies US Inc., AFCT-5715PZ-JU1 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
AFCT-5715PZ-JU1
Manufacturer Part Number
AFCT-5715PZ-JU1
Description
Manufacturer
Avago Technologies US Inc.
Datasheet
1.AFCT-5715PZ-JU1.pdf
(19 pages)
Specifications of AFCT-5715PZ-JU1
Optical Fiber Type
TX/RX
Data Transfer Rate
1250MBd
Optical Rise Time
0.26/0.4ns
Optical Fall Time
0.26/0.4ns
Jitter
0.227/0.267ns
Operating Temperature Classification
Commercial
Peak Wavelength
1355nm
Package Type
SFP
Operating Supply Voltage (min)
3.14V
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (max)
3.47V
Operating Temp Range
-10C to 85C
Mounting
Snap Fit To Panel
Pin Count
20
Lead Free Status / RoHS Status
Compliant
Table 8. Transceiver Timing Characteristics
Notes:
1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal.
3. Time from power on or falling edge of Tx_Disable to when the modulated optical output rises above 90% of nominal.
4. From power on or negation of TX_FAULT using TX_DISABLE.
5. Time TX_DISABLE must be held high to reset the laser fault shutdown circuitry.
6. Time from loss of optical signal to Rx_LOS Assertion.
7. Time from valid optical signal to Rx_LOS De-Assertion.
8. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below 10% of nominal. Measured
9. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the modulated optical output rises above 90% of
10. Time from fault to two-wire interface TX_FAULT (A2h, byte 110, bit 2) asserted.
11. Time for two-wire interface assertion of Rx_LOS (A2h, byte 110, bit 1) from loss of optical signal.
12. Time for two-wire interface de-assertion of Rx_LOS (A2h, byte 110, bit 1) from presence of valid optical signal.
13. From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is functional.
14. Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h).
15. Time from stop bit to completion of a 1-8 byte write command.
Table 9. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics
10
Parameter
Hardware TX_DISABLE Assert Time
Hardware TX_DISABLE Negate Time
Time to initialize, including reset of TX_FAULT
Hardware TX_FAULT Assert Time
Hardware TX_DISABLE to Reset
Hardware RX_LOS Assert Time
Hardware RX_LOS De-Assert Time
Software TX_DISABLE Assert Time
Software TX_DISABLE Negate Time
Software Tx_FAULT Assert Time
Software Rx_LOS Assert Time
Software Rx_LOS De-Assert Time
Analog parameter data ready
Serial bus hardware ready
Write Cycle Time
Serial ID Clock Rate
Parameter
Transceiver Internal Temperature Accuracy
Transceiver Internal Supply Voltage Accuracy
Transmitter Laser DC Bias Current Accuracy
Transmitted Average Optical Output Power Accuracy
Received Average Optical Input Power Accuracy
from falling clock edge after stop bit of write transaction.
nominal.
Symbol
t_off
t_on
t_init
t_fault
t_reset
t_loss_on
t_loss_off
t_off_soft
t_on_soft
t_fault_soft
t_loss_on_soft
t_loss_off_soft
t_data
t_serial
t_write
f_serial_clock
Symbol
T
V
I
P
P
INT
INT
INT
T
R
Min
± 3.0
± 0.1
± 10
± 3.0
± 3.0
Minimum
10
Units
°C
V
%
dB
dB
Maximum
10
1
300
100
100
100
100
100
100
100
100
1000
300
10
400
Notes
Valid from T
Valid over V
Percentage of nominal bias value
Valid from 100 PW to 500PW, avg
Valid from 10 PW to 500PW avg
Unit
μs
ms
ms
μs
μs
μs
μs
ms
ms
ms
ms
ms
ms
ms
ms
kHz
CC
C
= -40 °C to +85 °C
= 3.3 V ± 5%
Notes
Note 1
Note 2
Note 3
Note 4
Note 5
Note 6
Note 7
Note 8
Note 9
Note 10
Note 11
Note 12
Note 13
Note 14
Note 15