E2K-X4ME2 5M Omron, E2K-X4ME2 5M Datasheet - Page 13
![Proximity Sensors E2K-X4ME2 W/ 5 METER CABLE](/photos/17/82/178297/e2k-x_sml.jpg)
E2K-X4ME2 5M
Manufacturer Part Number
E2K-X4ME2 5M
Description
Proximity Sensors E2K-X4ME2 W/ 5 METER CABLE
Manufacturer
Omron
Series
E2K-Xr
Type
Proximity Sensorr
Specifications of E2K-X4ME2 5M
Proximity Sensor Sensing Distance
4mm
Proximity Sensor Sensing Distance Range
2 to 7mm
Proximity Sensor Switching Mode
NC
Mounting
Panel
Operating Temp Range
-25C to 70C
Operating Temperature Classification
Commercial
Operating Supply Voltage (min)
10V
Operating Supply Voltage (typ)
12/15/18/24V
Operating Supply Voltage (max)
30V
Pin Count
3
Output Type
NPN
Maximum Operating Temperature
+ 70 C
Supply Voltage
12 VDC to 24 VDC
Supply Current
15 mA
Output Voltage
1 V
Operating Supply Voltage
10 VDC to 30 VDC
Mounting Style
Panel
Sensing Distance
4 mm
Minimum Operating Temperature
- 25 C
Current Rating
200 mA
Features
Permits non-contact detection of metallic and non-metallic objects
Voltage Rating
24 VDC
Lead Free Status / RoHS Status
Supplier Unconfirmed
Note: When AND/OR connections are used with Proximity Sensors, the effects of erroneous pulses or leakage current may prevent use. Verify that there are no
Extending Cable Length
The cable of a Built-in Amplifier Sensor can be extended to a
maximum length of 200 m with each of the standard cables
(excluding some models).
For Separate Amplifier Sensors (E2C-EDA, E2C, E2J, E2CY), refer
to the specific precautions for individual products.
Bending the Cable
If you need to bend the cable, we recommend a bend radius that is at
least 3 times the outer diameter of the cable (with the exception of
coaxial and shielded cables).
Cable Tensile Strength
In general, do not subject the cable to a tension greater than that
indicated in the following table.
Note: Do not subject a shielded cable or coaxial cable to tension.
Separating High-voltage Lines
Using Metal Conduits
If a power line is to be located near the Proximity Sensor cable, use a
separate metal conduit to prevent malfunction or damage. (Same for
DC models.)
Cable diameter
Less than 4 mm
DC 3-wire
Model
4 mm min.
problems before use.
connection
AND (series
connection)
OR (parallel
connection)
http://www.ia.omron.com/
Type of
Tensile strength
30 N max.
50 N max.
(A)
(B)
+
+
+
-
+
-
-
-
OUT
OUT
OUT
OUT
iL
i
i
Connection
Load
Load
Vs
Vs
Proximity Sensors Technical Guide
Example of Connection with S3D2 Sensor Controller
Using the S3D2 Sensor Controller
Operation can be reversed with the signal input
switch on the S3D2.
Connecting to a Relay Load
Note: DC 2-Wire Sensors have a residual voltage of 3 V. Check the operating
Operation can be reversed with the signal input
switch on the S3D2.
Keep the number of connected Sensors (N) within the range of the following
equation.
iL + (N - 1) × i ≤ Upper limit of Proximity Sensor control output
V
Note: When an AND circuit is connected, the operation of Proximity Sensor B
For Sensors with a current output, a minimum of three OR connections is pos-
sible. Whether or not four or more connections is possible depends on the
model.
S
N : Number of Sensors that can be con-
V
V
i : Current consumption of Sensor
iL: Load current
- N × V
DC 2-Wire Sensors
DC 3-Wire Sensors
R
S
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
: Power supply voltage
: Residual output voltage of Sensor
voltage of the relay before use.
The residual voltage of the E2E-XD-M1J-T is 5 V.
nected
causes power to be supplied to Proximity Sensor A, and thus erroneous
pulses (approximately 1 ms) may be generated in A when the power is
turned ON. For this reason, take care when the load has a high
response speed because malfunction may result.
R
≥ Operating load voltage
Brown
Blue
Description
X
24 VDC
Example: A maximum of two
Sensors can be used when an
MY (24-VDC) Relay is used for
the load.
Blue 0 V
Brown OUT
Blue 0 V
Black OUT
Brown +12 V
S3D2
S3D2
10
10
7
4
1
7
4
1
11
11
8
5
2
8
5
2
12
12
9
6
3
9
6
3
C-7