FNP600-48G POWER ONE, FNP600-48G Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/5/534/power_one_sml.jpg)
FNP600-48G
Manufacturer Part Number
FNP600-48G
Description
Linear & Switching Power Supplies Front End 600W (48V)
Manufacturer
POWER ONE
Datasheet
1.FNP600-48G.pdf
(15 pages)
Specifications of FNP600-48G
Input Voltage
90 to 264V
Output Voltage
48V
Number Of Outputs
1
Output Power (max)
600W
Input Frequency
47 to 63Hz
Screening Level
Commercial
Product Length (mm)
298.2mm
Product Height (mm)
40.6mm
Product Depth (mm)
83.8mm
Operating Temperature Min Deg. C
0C
Operating Temperature Max Deg. C
70C
Mounting Style
Desktop
Product
Switching
Lead Free Status / RoHS Status
Compliant
Lead Free Status / RoHS Status
Compliant
Output Specifications
Protection
BCD20034-G Rev. AD, 11-May-10
1
2
FNP1000-48 overvoltage protection range is 56 V minimum and 60 V maximum.
A pull-up to 3.3V can be achieved by terminating the logic signal with a 10 kΩ resistor to logic ground.
Efficiency:
Minimum Load
Output Power
Overshoot
Transient Response
Turn-On Delay
Output Regulation
Overvoltage
Protection
Overcurrent
Protection
(Power supply
recovers when short
is removed.)
Short-Circuit
Protection
Overtemperature/
Fan Failure Warning
Parameter
FNP1000-48
FNP600-12
FNP850-12
FNP600-48
FNP1000
FNP850
FNP600
Parameter
Full rated load at 230 VAC input.
Minimum loading required to maintain regulation.
Output voltage overshoot at turn-on.
Maximum recovery time to within 1% of initial set
point due to a 50% load change, 1A/µs.
Maximum deviation:
Time required for initial output voltage stabilization
after application of AC input..
See Model Selection table.
FNP600-12 &
FNP850-12
FNP600-12:
FNP850-12:
FNP600-48 &
FNP1000-48
FNP600-12
FNP850-12
FNP600-48
FNP1000-48
FNP 12V or 48V Vo1 supply output will shut down in the event of an overtemperature condition or blocked
fan rotor. Supply's fan and Vaux are active. Power supply will recover when OT condition is removed.
Amber OT LED will turn ON to indicate fault condition.
OT/Fan Fail is an open-collector signal with 20-mA pull-down. High signal indicates a normal operating
condition. Output will go low at least 100 ms before OT condition shuts down the power supply. Internally
pulled up to 5V with a 5.1 kΩ resistor. Note.
Conditions/Description
& FNR-5-12G/FNR-5-48G Power Shelves Data Sheet
Latch-style overvoltage protection.
Output adjusted to 12V:
Latch-style overvoltage protection.
Output adjusted to 7V:
Latch-style overvoltage protection.
Output adjusted to 48V:
Current limit.12V output:
12V Standby output:
Current limit.12V output:
12V Standby output:
Current limit.48V output:
12V Standby output:
Current limit.48V output:
12V Standby output:
12V or 48V output:
12V or 48V output:
Page 3 of 15
Power supply recovers when short is removed.
Conditions/Description
Standby output:
Standby output:
FNP600/850/1000 AC-DC Front-Ends
2
Min.
88
88
84
84
0
Min.
14.4
8.75
8.44
0.55
0.55
0.75
0.75
57
Nom.
54
77
13
22
89.5
89.5
87
87
1
Nom.
9.04
8.75
0.75
0.75
15
56
80
14
23
www.power-one.com
Max.
1006
856
600
400
1.5
3
2
2
4
Max.
15.6
9.33
1.75
1.75
9.1
1.0
1.0
60
61
88
16
25
Units
Sec
Units
ms
µs
W
%
%
%
%
A
V
V
V
A
A
A
A