LD400600 Red Lion Controls, LD400600 Datasheet - Page 11
![COUNTER 6 DIGIT 4.0" 120VAC RED](/photos/6/45/64523/mfg_ld_series_sml.jpg)
LD400600
Manufacturer Part Number
LD400600
Description
COUNTER 6 DIGIT 4.0" 120VAC RED
Manufacturer
Red Lion Controls
Series
LDr
Type
Counterr
Specifications of LD400600
Count Rate
35kHz
Number Of Digits/alpha
6
Input Type
Voltage, Switch Closure, Transistor Switch
Voltage - Supply
11 V ~ 16 VDC, 85 V ~ 250 VAC
Display Type
LED Red
No. Of Digits / Alpha
6
Digit Height
101mm
Power Consumption
26VA
Counting Speed
25kHz
Operating Temperature Range
0°C To +50°C
Signal Input Type
Pulse
Character Size
4"
Ip/nema Rating
IP65 / NEMA 4X
Connection Type
Wire Leads
Dimensions
26"L×2.25"W×7.875"H
Display Digit Height
4 "
Function
Counter
Material, Casing
Aluminum
Number Of Digits
4
Primary Type
Electronic
Special Features
RS485/RS232 Communications
Termination
Terminal Block
Voltage, Supply
85 to 250/11 to 16 VAC/VDC
Counter Supply Voltage
85-250VAC/11-16VDC
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Output Type
-
Lead Free Status / Rohs Status
RoHS Compliant part
display then returns to
“
selected setpoint is completely programmed, the display returns to
Repeat steps for Setpoint 2 if both Setpoints are being used. Select
Setpoint programming module.
Output Action selected. The Setpoint Parameter Availability chart below illustrates this.
5.4 MODULE 4 - S
Select
” in the following parameters reflects the chosen Setpoint number. After the
Entering Code 50 will display the model and version (x.x) of the meter. The
Select the Setpoint Output to be programmed, starting with Setpoint 1. The
Some Setpoint parameters will not appear depending on the Setpoint Assignment and Setpoint
PAR
* BOUNDARY Setpoint Action not applicable for Counter B assignment.
PARAMETER
Setpoint
Select
to perform either of the Factory Service Operations shown below.
VIEW MODEL AND VERSION DISPLAY
FACTORY SERVICE OPERATIONS
Setpoint Output
Power-up
Setpoint Output Time-out Value
Setpoint Value
Setpoint Output Logic
Setpoint Annunciator
Setpoint Output Power-up State
Setpoint Boundary Type
Standby Operation (Low ActingOnly)
Counter Auto Reset
SP1 Output Off at SP2 (SP1 only)
SP2 Output Off at SP1 (SP2 only)
Output Reset with Manual Reset
SETPOINT SELECT
State
Setpoint
Enable
. Press the
DESCRIPTION
Boundary
Setpoint
PAR
Assignment
Type
Setpoint
key to exit the module.
ETPOINT
Operation
Standby
Setpoint
Setpoint
Output
Action
PARAMETER MENU
TIMED OUT
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
to exit the
COUNTER ASSIGNMENT (A or B)*
O
Auto Reset
Counter
Setpoint
Time-out
UTPUT
Output
.
BOUNDARY
11
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
settings. The meter will display
PAR
Entering Code 66 will overwrite all user settings with the factory default
Select
SP1 Output
Off at SP2
is selected, the unit returns to
SP1 Only
key to exit the module.
Output
Setpoint
P
Value
LATCH
ARAMETERS
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
RESTORE FACTORY DEFAULT SETTINGS
No
No
No
to enable the chosen setpoint and access the setup parameters. If
SP2 Output
Off at SP1
SP2 Only
Output
Output Logic
Setpoint
TIMED OUT
SETPOINT ENABLE
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
Output Reset
RATE ASSIGNMENT
with Manual
Setpoint
Reset
BOUNDARY
Annunciator
(
and then return to
Setpoint
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
and the setpoint is disabled.
)
LATCH
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
. Press the