MAX9315EUP+ Maxim Integrated Products, MAX9315EUP+ Datasheet - Page 6
![IC DRIVER DIFF 1:5 20-TSSOP](/photos/6/52/65243/175-20-tssop_sml.jpg)
MAX9315EUP+
Manufacturer Part Number
MAX9315EUP+
Description
IC DRIVER DIFF 1:5 20-TSSOP
Manufacturer
Maxim Integrated Products
Type
Fanout Buffer (Distribution), Multiplexer , Datar
Datasheet
1.MAX9315EUP.pdf
(11 pages)
Specifications of MAX9315EUP+
Number Of Circuits
1
Ratio - Input:output
2:5
Differential - Input:output
Yes/Yes
Input
HSTL, LVECL, LVPECL
Output
LVECL, LVPECL
Frequency - Max
1.5GHz
Voltage - Supply
2.25 V ~ 3.8 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
20-TSSOP
Frequency-max
1.5GHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The MAX9315 is a low-skew, 1-to-5 differential driver
designed for clock or data distribution. A 2-to-1 MUX
selects one of the two differential clock inputs, CLK0,
CLK0 or CLK1, CLK1. The MUX is switched by the sin-
gle-ended SEL input. A logic low selects the CLK0,
CLK0 input and a logic high selects the CLK1, CLK1
input. The SEL logic threshold is set by the internal volt-
age reference V
or by a single-ended LVPECL/LVECL signal. The
selected input is reproduced at five differential outputs.
The MAX9315 is synchronously enabled and disabled
with outputs in the low state to eliminate shortened
clock pulses. EN is connected to the input of an edge-
triggered D flip-flop. After power-up, drive EN low and
1:5 Differential LVPECL/LVECL/HSTL
Clock and Data Driver
6
18, 20
_______________________________________________________________________________________
PIN
10
11
12
13
14
15
16
17
19
1
2
3
4
5
6
7
8
9
BB
NAME
CLK0
CLK0
CLK1
CLK1
V
V
SEL
V
Q0
Q0
Q1
Q1
Q2
Q2
Q3
Q3
Q4
Q4
EN
CC
. SEL can be driven to V
BB
EE
Detailed Description
Noninverting Q0 Output. Typically terminate with 50Ω resistor to V
Inverting Q0 Output. Typically terminate with 50Ω resistor to V
Noninverting Q1 Output. Typically terminate with 50Ω resistor to V
Inverting Q1 Output. Typically terminate with 50Ω resistor to V
Noninverting Q2 Output. Typically terminate with 50Ω resistor to V
Inverting Q2 Output. Typically terminate with 50Ω resistor to V
Noninverting Q3 Output. Typically terminate with 50Ω resistor to V
Inverting Q3 Output. Typically terminate with 50Ω resistor to V
Noninverting Q4 Output. Typically terminate with 50Ω resistor to V
Inverting Q4 Output. Typically terminate with 50Ω resistor to V
Negative Supply Voltage
Clock Select Input (Single Ended). Drive low to select the CLK0, CLK0 input. Drive high to select the
CLK1, CLK1 input. The SEL threshold is equal to V
Noninverting Differential Clock Input 0. Internal 75kΩ pulldown to V
Inverting Differential Clock Input 0. Internal 75kΩ pullup to V
Reference Output Voltage. Connect to the inverting or noninverting clock input to provide a
reference for single-ended operation. When used, bypass with a 0.01µF ceramic capacitor to V
otherwise, leave open.
Noninverting Differential Clock Input 1. Internal 75kΩ pulldown to V
Inverting Differential Clock Input 1. Internal 75kΩ pullup to V
Positive Supply Voltage. Bypass V
capacitors as close to the device as possible with the smaller value capacitor closest to the device.
Output Enable Input. Outputs are synchronously enabled on the falling edge of the selected clock
input when EN is low. Outputs are synchronously driven low on the falling edge of the selected
clock input when EN is high.
Synchronous Enable
CC
and V
EE
CC
to V
toggle the selected clock input to enable the outputs.
The outputs are enabled on the falling edge of the
selected clock input after EN goes low. The outputs are
set to a low state on the falling edge of the selected
clock input after EN goes high. The threshold for EN is
equal to V
For interfacing to differential HSTL and LVPECL signals,
the V
grounded), allowing high-performance clock or data
distribution in systems with a nominal +2.5V or +3.3V
supply. For interfacing to differential LVECL, the V
range is -2.375V to -3.8V (with V
levels are referenced to V
LVPECL or LVECL, depending on the level of the V
supply. With V
EE
CC
with 0.1µF and 0.01µF ceramic capacitors. Place the
FUNCTION
range is from +2.375V to +3.8V (with V
BB
BB
.
.
CC
connected to a positive supply and
CC
CC
CC
CC
CC
CC
CC
and 75kΩ pulldown to V
and 75kΩ pulldown to V
- 2V.
- 2V.
- 2V.
- 2V.
- 2V.
CC
CC
CC
CC
CC
EE
EE
- 2V.
- 2V.
- 2V.
- 2V.
- 2V.
.
.
CC
Pin Description
CC
and are considered
grounded). Output
EE
EE
.
.
Supply
CC
;
CC
EE
EE