1-6605310-1 TE Connectivity, 1-6605310-1 Datasheet - Page 2

• Manufacturer Part Number: 1-6605310-1
• Description: 1X1 MAG45 4DN2, 315 VOIP G/G R
• Manufacturer: TE Connectivity
• Series: Mag45r

Specifications of 1-6605310-1

• Product: Telecom & Ethernet Connectors
• Usoc Codes: RJ45
• Mounting Style: Through Hole
• Number Of Ports: 1
• Gender: Female
• Shielding: Shielded
• Contact Plating: Gold over Nickel
• Housing Material: Thermoplastic Polyethylene Terephthalate Polyester
• Contact Material: Phosphor Bronze
• Flammability Rating: UL 94 V-0
• Mounting Angle: Right Angle
• Number Of Rows: 1
• Operating Temperature Range: 0 C to + 70 C
• Termination Style: Solder
• Product Type: Connector
• Number Of Cores: 6
• Magnetics: Integrated Magnetics
• Jack Type: RJ45
• Power Over Ethernet (poe) Type: Enabled Power
• Signal Routing Type: Auto MDI/MDIX
• Profile: Standard
• Pcb Mounting Orientation: Side Entry (Right Angle)
• Jack Configuration: 1 x 1
• Turns Ratio: 1:1
• Shielded: Yes
• Emi Finger - Bottom: Without
• Termination Method: Solder
• Port Configuration: Single
• Emi Fingers -top And Sides: With
• Latch Orientation: Standard - Latch Down
• Pcb Tail Length (mm [in]): 3.68 [0.145]
• Contact Termination Type: Through Hole
• Preloaded: Yes
• Connector Style: Jack
• Status Indicator: LED
• Decoupling Capacitor: Without
• Rear Pcb Ground Tab: Without
• Signal Lead Quantity: 8
• Rohs/elv Compliance: Not ELV/RoHS compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Left Led Color (position #1): Green - 250 ohm resistor
• Right Led Color (position #2): Green - 250 ohm resistor
• Operating Temperature (°c [°f]): 0 – 70 [32 – 158]
• Applies To: Printed Circuit Board
• Environmental Conditions: Office / Premises
• Application: 10/100 POE
• Lead Free Status / Rohs Status: Details

3.4.
3.5.
3.6.
Examination of product.
Dry circuit resistance.
Open circuit inductance.
Random vibration, operational.
Random vibration, non-operational.
Rev D
●
Product Codes
Product Codes for this product family are H363, H364, H365 and H366
Performance and Test Description
Product is designed to meet the electrical, mechanical and environmental performance requirements
specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental
conditions per EIA-364.
Test Requirements and Procedures Summary
Test Description
Temperature:
•
•
Standard: 0 to 70° C |
Extended temperature varieties: -40 to 85° C
Meet requirements of product
drawing, and dimensional and
plating requirements of FCC Part
68, Subpart F, Connector
Specification per Figure
68.500(d)(2)(i) 8 Position Series
Modular Jack.
See Engineering Report 502-1129.
OCL 350 µH minimum.
No discontinuities of 1
microsecond
or longer duration.
See Note.
See Note.
R 30 milliohms maximum.
Figure 1 (continued)
MECHANICAL
ELECTRICAL
Requirement
Measure per drawing, inspect
plating thickness per x-ray
evaluation per EIA-364-48 Method
C.
EIA-364-23A.
Subject specimens to 100 mA
maximum and 20 mV maximum
open circuit voltage.
See Figure 3.
ANSI X3.263, ref IEEE 802.3.
Measure and record mutual
inductance of mated and mounted
specimens at 100 kHz, 100 mV, 8
mA DC bias, and 25° C.
EIA-364-28D,
Test Condition VIIA.
Subject specimens to 1.0 G rms
between 3-500 Hz. PSD of .003.
45 minutes in each of 3 mutually
perpendicular planes.
EIA-364-28D,
Test Condition VIIA.
Subject specimens to 1.0 G rms
between 3-500 Hz. PSD of .003.
45 minutes in each of 3 mutually
perpendicular planes.
Procedure
108-2100
2 of 6