1-6605310-1 TE Connectivity, 1-6605310-1 Datasheet - Page 5

• Manufacturer Part Number: 1-6605310-1
• Description: 1X1 MAG45 4DN2, 315 VOIP G/G R
• Manufacturer: TE Connectivity
• Series: Mag45r

Specifications of 1-6605310-1

• Product: Telecom & Ethernet Connectors
• Usoc Codes: RJ45
• Mounting Style: Through Hole
• Number Of Ports: 1
• Gender: Female
• Shielding: Shielded
• Contact Plating: Gold over Nickel
• Housing Material: Thermoplastic Polyethylene Terephthalate Polyester
• Contact Material: Phosphor Bronze
• Flammability Rating: UL 94 V-0
• Mounting Angle: Right Angle
• Number Of Rows: 1
• Operating Temperature Range: 0 C to + 70 C
• Termination Style: Solder
• Product Type: Connector
• Number Of Cores: 6
• Magnetics: Integrated Magnetics
• Jack Type: RJ45
• Power Over Ethernet (poe) Type: Enabled Power
• Signal Routing Type: Auto MDI/MDIX
• Profile: Standard
• Pcb Mounting Orientation: Side Entry (Right Angle)
• Jack Configuration: 1 x 1
• Turns Ratio: 1:1
• Shielded: Yes
• Emi Finger - Bottom: Without
• Termination Method: Solder
• Port Configuration: Single
• Emi Fingers -top And Sides: With
• Latch Orientation: Standard - Latch Down
• Pcb Tail Length (mm [in]): 3.68 [0.145]
• Contact Termination Type: Through Hole
• Preloaded: Yes
• Connector Style: Jack
• Status Indicator: LED
• Decoupling Capacitor: Without
• Rear Pcb Ground Tab: Without
• Signal Lead Quantity: 8
• Rohs/elv Compliance: Not ELV/RoHS compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Left Led Color (position #1): Green - 250 ohm resistor
• Right Led Color (position #2): Green - 250 ohm resistor
• Operating Temperature (°c [°f]): 0 – 70 [32 – 158]
• Applies To: Printed Circuit Board
• Environmental Conditions: Office / Premises
• Application: 10/100 POE
• Lead Free Status / Rohs Status: Details

4.
4.1.
4.2.
4.3.
4.4.
Rev D
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets the requirements of Figure 1. Failures
attributed to equipment, test setup or operator deficiencies shall not disqualify the product. If product
failure occurs, corrective action shall be taken and specimens resubmitted for qualification. Testing to
confirm corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan shall specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
Specimen Selection
Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. Test group 1 shall consist of 16 specimens. Test
groups 2 and 3 shall each consist of 1 specimen. Test group 4 shall consist of 45 specimens.
Test Sequence
Qualification inspection shall be verified by testing specimens as specified in Figure 2.
108-2100
5 of 6