1-968855-1 TE Connectivity, 1-968855-1 Datasheet - Page 2

• Manufacturer Part Number: 1-968855-1
• Description: MCP2,8 SOCKET CONT SWS
• Manufacturer: TE Connectivity
• Series: HDSCS, J2557 Connector System, Multiple Contact Point (MCP), Standard Timerr

Specifications of 1-968855-1

• Rohs Compliant: YES
• Product Type: Contact
• Mating Area Interface Dimensions (mm [in]): 2.79 x 0.81 [.110 x .032]
• Wire/cable Type: Regular Wire
• Insulation Support: With
• Wire Range (mm [awg]): 0.50-1.00² [20-17]
• Single Wire Sealing System: Yes
• Single Seal Part No.: 828904-1
• Contact Type: Socket
• Contact Base Material: CuNiSi
• Contact Plating, Mating Area, Material: Pre-Tin
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Applies To: Wire/Cable
• Cavity Plug Part No.: 828922
• Packaging Method: Strip

3.2.
3.3.
3.4.
3.5.
Rev A
Exam ination of product.
Term ination resistance, dry circuit.
Dielectric withstanding voltage.
Tem perature rise vs current.
Fuse blow.
Materials
!
!
!
!
!
Ratings
!
!
!.
Perform ance and Test Description
Product is designed to m eet the electrical, m echanical and environm ental perform ance requirem ents
specified in Figure 1. Unless otherwise specified, all tests shall be perform ed at am bient environm ental
conditions per EIA-364.
Test Requirem ents and Procedures Sum m ary
Test Description
Base: PBT GF30, Valox 420SE0, flam m ability rating V-0
Cover: Valox 310SE0, non reinforced PBT, flam m ability rating V-0
Seal: Silicone rubber
Term inals: TE MCP 2.8 m m system , sealed, 14-18 AW G Product Specification 108-18513-0
W ire seal: Silicone rubber
Current: Refer to TE MCP 2.8 m m term inal system , part num ber 1-968857-1 sealed term inal 14-
16 AW G, part num ber 1-968855-1 sealed term inal 18 AW G for electrical rating and heat rise
characteristics
Tem perature: -40 to 65°C
Seal: Dust proof, SAEJ1455, 4.7.3, splash proof, IP X4
10 m illiohm s m axim um .
Meets requirem ents of product
drawing.
Two m inute hold with no cross
over.
Shall not exceed MCP 2.8 m m
contact specification for 9 position
housing, Product Specification 108-
18513-0.
No plastic or term inal interface
degradation.
Figure 1 (continued)
ELECTRICAL
Requirem ent
EIA-364-23A.
Visual, dim ensional and functional
per applicable quality inspection
plan.
Subject specim ens to 100
m illiam peres m axim um and 20
m illivolts m axim um open circuit
voltage.
EIA 364-21C
Apply 500 volts DC between
adjacent term inals.
EIA 364-70A and IEC 60512-5-1.
30 am pere term inals m ust be
separated by 10 am pere m axim um
term inals. Loading configuration per
Figure 3. For interm ittent use of 30
am pere current, the heat rise curve
shown in Figure 4 applies.
Subject each fuse under load to full
12 volts DC battery voltage and
current until the fuse “opens” for a
total of 5 tim es per fused circuit
under load.
Procedure
108-47001
2 of 8