CDP68HC68T1M96 Intersil, CDP68HC68T1M96 Datasheet - Page 10
![IC RTC RAM/SPI SERIAL 20-SOIC](/photos/6/58/65875/20-20-soic_sml.jpg)
CDP68HC68T1M96
Manufacturer Part Number
CDP68HC68T1M96
Description
IC RTC RAM/SPI SERIAL 20-SOIC
Manufacturer
Intersil
Type
Clock/Calendar/NVSRAMr
Datasheet
1.CDP68HC68T1EZ.pdf
(23 pages)
Specifications of CDP68HC68T1M96
Memory Size
32B
Time Format
HH:MM:SS (12/24 hr)
Date Format
YY-MM-DD-dd
Interface
SPI, 3-Wire Serial
Voltage - Supply
3 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
20-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
CLK OUT
Clock output pin. One of seven frequencies can be selected
(or this output can be set low) by the levels of the three
LSB’s in the Clock-Control Register. If a frequency is
selected, it will toggle with a 50% duty cycle except 2Hz in
the 50Hz time base mode. (e.g. if 1Hz is selected, the output
will be high for 500ms and low for the same period). During
power-down operation (Bit 6 in Interrupt Control Register is
set to “1”), the clock-output pin will be set low.
CPUR
CPU reset output pin. This pin functions as an N-Channel
only, open-drain output and requires an external pull-up
resistor.
INT
Interrupt output pin. This output is driven from a single NFET
pulldown transistor and must be tied to an external pull-up
resistor. The output is activated to a low level when:
The Status Register must be read to set the Interrupt output
high after the selected periodic interval occurs. This is also
true when conditions 1 and 2 activate the interrupt. If
power-down had been previously selected, the interrupt will
also reset the power-down functions.
2. The second condition that releases Power-Down occurs
1. Power-sense operation is selected (B5 = 1 in Interrupt
2. A previously set alarm time occurs. The alarm bit in the
3. A previously selected periodic interrupt signal activates.
FIGURE 6. POWER-UP FUNCTIONAL DIAGRAM (INITIATED
when the level on the V
the level at the V
level of V
or V
Supply Mode.
Control Register) and a power failure occurs.
Status Register and interrupt-out signal are delayed
30.5µs when 32kHz operation is selected and 15.3µs for
2MHz and 7.6µs for 4MHz.
SYS
falls to logic low and returns high in the Single
BATT
BY A RISE IN VOLTAGE ON THE “V
V
BATT
(see Figure 6) in the Battery Backup Mode
BATT
V
SYS
REAL-TIME CLOCK
INTERFACE
input, after previously falling to the
SYS
CDP68HC68T1
SERIAL
10
pin rises about 1.0V above
CPUR
CLK
OUT
PSE
MISO
MOSI
SYS
” PIN)
CDP68HC68T1
SCK, MOSI, MISO
See “Serial Peripheral Interface (SPI)” on page 8.
CE
A positive chip-enable input. A low level at this input holds
the serial interface logic in a reset state. This pin is also used
for the watchdog function.
V
The negative power-supply pin that is connected to ground.
PSE
Power-supply enable output pin. This pin is used to control
power to the system. The pin is set high when:
The PSE pin is set low by writing a high into bit 6
(power-down bit) in the Interrupt Control Register.
POR
Power-on reset. A Schmitt-trigger input that generates a
power-on internal reset signal using an external RC
network. Both control registers and frequency dividers for
the oscillator and line input are reset. The Status Register
is reset except for the first time up bit (B4), which is set.
Single supply or battery backup operation is selected at the
end of POR.
LINE
This input is used for two functions. When not used it
should be connected to V
function utilizes the input signal as the frequency source for
the timekeeping counters. This function is selected by
setting Bit 6 in the Clock Control Register. The second
function enables the line input to sense a power failure.
Threshold detectors operating above and below V
an AC voltage loss. Bit 5 must be set to “1” in the Interrupt
Control Register and crystal or external clock source
operation is required. Bit 6 in the Clock Control Register
must be low to select XTAL operation.
Oscillator Circuit
The CDP68HC68T1 has an on-board 150kΩ resistor that is
switched in series with its internal inverter when 32kHz is
selected via the Clock Control Register. Note: When first
powered up the series resistor is not part of the oscillator
circuit. (The CDP68HC68T1 sets up for a 4MHz oscillator).
1. V
2. An interrupt occurs.
3. A power-on reset (if V
SS
placed low by a system failure.
SYS
rises above the V
SYS
DD
BATT
via a 10kΩ resistor. The first
is a logic high).
voltage after V
SYS
October 29, 2007
DD
was
FN1547.8
sense